Technische Daten - AEG BSB 18CBL Manual Original

Ocultar thumbs

página de 55

/ 55
Marcadores

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C

and away from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods

Legislation requirements.

Transportation of those batteries has to be done in

accordance with local, national and international provisions

and regulations.

• The user can transport the batteries by road without further

requirements.

• Commercial transport of Lithium-Ion batteries by third

parties is subject to Dangerous Goods regulations.

Transport preparation and transport are exclusively to be

carried out by appropriately trained persons and the

process has to be accompanied by corresponding experts.

When transporting batteries:

• Ensure that battery contact terminals are protected and

insulated to prevent short circuit.

• Ensure that battery pack is secured against movement

within packaging.

• Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice

BATTERY PACK PROTECTION

The battery pack has overload protection that protects it from

being overloaded and helps to ensure long life.

Under extreme stress the battery electronics switch oﬀ the

machine automatically. To restart, switch the machine oﬀ and

then on again. If the machine does not start up again, the

battery pack may have discharged completely. In this case it

must be recharged in the battery charger.

MAINTENANCE

Use only AEG accessories and spare parts. Should

components need to be replaced which have not been

described, please contact one of our AEG service agents

(see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered.

Please state the machine type printed as well as the six-digit

No. on the label and order the drawing at your local service

agents or directly at: Techtronic Industries GmbH,

Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

CAUTION! WARNING! DANGER!

Remove the battery pack before starting any work

on the machine.

Please read the instructions carefully before

starting the machine.

Do not dispose electric tools, batteries/

rechargeable batteries together with household

waste material.

Electric tools and batteries that have reached the

end of their life must be collected separately and

returned to an environmentally compatible

recycling facility.

Check with your local authority or retailer for

recycling advice and collection point.

No-load speed

ENGLISH

Volts

Direct current

European Conformity Mark

British Confomity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark

TECHNISCHE DATEN

AKKU-BOHRSCHRAUBER

Produktionsnummer ................................................................

Bohr-ø in Stahl.........................................................................

Bohr-ø in Holz..........................................................................

Bohr-ø in Ziegel und Kalksandstein.........................................

Holzschrauben (ohne Vorbohren)............................................

Leerlaufdrehzahl 1.Gang / 2. Gang .........................................

Schlagzahl 1.Gang / Schlagzahl 2.Gang .................................

Drehmoment * (2,0 Ah) ............................................................

Drehmoment * (4,0 Ah) ............................................................

Spannung Wechselakku ..........................................................

Bohrfutterspannbereich ...........................................................

Gewicht nach EPTA-Prozedur 01/2014 (1,5 Ah / 2,0 Ah) ........

Gewicht nach EPTA-Prozedur 01/2014 (3,0 Ah / 4,0 Ah) ........

Empfohlene Umgebungstemperatur beim Arbeiten.................

Empfohlene Akkutypen ............................................................

Empfohlene Ladegeräte ..........................................................

Geräusch/Vibrationsinformation

Messwerte ermittelt entsprechend EN 62841.

Der A-bewertete Geräuschpegel des Gerätes beträgt typischerweise:

Schalldruckpegel (Unsicherheit K=3dB(A)) .............................

Schallleistungspegel (Unsicherheit K=3dB(A)) ........................

Gehörschutz tragen!

Schwingungsgesamtwerte (Vektorsumme dreier Richtungen)

ermittelt entsprechend EN 62841.

Bohren in Metall, Bohrfutterkopf

Schwingungsemissionswert a

...........................................

h,D