Technical Specifications - IMER SYNTESI S 190 Manual De Uso, Mantenimiento Y Recambios

GB
Dear customer,
congratulations on your choice of purchase: the IMER CON-
CRETE MIXER, the result of years of experience, is a very
reliable machine equipped with all the latest technical
innovations.
WORKING IN SAFETY
In order to be able to work in complete safety, the following
instructions must be read carefully.
This OPERATING AND MAINTENANCE manual must be kept on
site by the person responsible for the worksite, e.g. the site
foreman, and must always be available for consultation.
The manual should be considered as being an integral part of the
machine, and must be kept for future reference (EN 292/2) until
the machine itself is disposed of. If the manual becomes damaged
or lost, a replacement can be obtained from the manufacturer.
The manual contains important information regarding the site
preparation, installation, use of the machine, maintenance and
spare parts ordering. Nevertheless, the installer and user must
both have adequate experience and knowledge of the machine.
In order that the safety of the operator, safe working and long life
of the equipment can all be guaranteed, the instructions in this
manual must be followed together with safety standards and
health and safety at work laws currently in force (use of suitable
footwear and clothing, use of helmets, gloves and goggles, etc.).
- Always make sure that signs are legible
- It is strictly forbidden to carry out any form of
modification to the structure or working parts of the
machine.
IMER INTERNATIONAL decline any responsibility in the case of
non-compliance with laws and standards governing the use of
this equipment. In particular: improper use, defective power supply,
lack of maintenance, unauthorised modifications, partial or total
failure to comply with instructions contained in this manual.
IMER reserves the right to modify the characteristics of the con-
crete mixer and/or the contents of this manual without any
obligation to update previous machines or manuals.

1. TECHNICAL SPECIFICATIONS

Table 1 reports the technical specifications of the concrete mixer,
with reference to figure 1.
2. DESIGN STANDARDS
The concrete mixers have been designed and built in accordance
with the following standards: EN 292-1-2, EN 60204-1, prEN 12151.
Concrete mixer model
Concrete mixer code
Drum capacity
Mix capacity
Effective output
Number of drum rpm's
Direction of drum rotation
Concrete mixer weight
Wheel dimensions
.Electric motor power
Voltage (single phase)
Nominal current
Frequency
Number of electric motor rpm's
Protection grade
Total concrete mixer length (L)
Total concrete mixer height (H)
Total concrete mixer width (B)
IMER INTERNATIONAL S.p.A.
S 190 - S 250 - S 300 - S 350 EL
- TABLE
S 190 EL
1105650 1105700 1105703
l 190
l 160
l 120
24
Anti-clock wise
Kg 106
mm 295x54
KW 1
V 230
A 5
Hz 50
n/1' 2.850
IP 55
cm 146,5
cm 133,4
cm 79,3
9
3. NOISE EMISSION LEVEL
Table 2 indicates the noise level produced by the mixer, measured
at the operator's ear (L at 1 m - 98/37CE) and the environmental
pA
noise emission level (power L
EN ISO 3744 (2000/14/CE).
TABLE 2
CONCRETE
TYPE OF MOTOR
MIXER
S 190 EL
ELECTRIC
S 250 EL
S 300 EL
ELECTRIC
S 350 EL
4. DESCRIPTION AND OPERATION
- The concrete mixer is designed for use on
construction sites, for preparing and mixing concrete,
mortars, cement mixes, etc.
- Use of the machine is unadvisable with temperatures
below 0° C.
CEMENT MIXER WITH ELECTRIC MOTOR (FIG. 1)
The cement mixer comprises a frame (ref. 1) with two hard wheels
(ref. 2), an arm (ref. 3) onto which the gear unit is attached (ref. 4),
driven by a poly-V belt (ref. 5) which is driven in turn by the electric
motor (ref. 6).
The mixing drum (ref. 7) is mounted on the gear unit: the drum bush is
fitted onto the gearbox's tapered output shaft by inserting the pin into
the slot on the drum bush. The mixing drum is secured onto the gear
shaft using a screw.
Drum tilting is controlled by manual rotation of the handwheel (ref. 8),
which acts on the worm – wheel gear unit (ref. 9), connected to the
arm.
The electric motor is switched on and off using the two pushbuttons
on the electric control panel (ref. 10).
The electric control panel has a plug (ref. 11) for connection to power
supply.
To transport the concrete mixer on site (with drum empty) use the
steering gear (ref. 12) which can be extracted from the frame.
5. SAFETY INSTRUCTIONS
- Before using machine ensure all safety devices
are fit ted
- Kee p all par ts of bod y and/or tools cle ar of
mi xin g d rum dur ing op era tio n.
Accident prevention standards and safety regulations must be
observed at all times in the work area.
When handling the components required to prepare the mixes,
1 -
S 250 EL S 300 EL
1105750
235 314
190 250
140 190
24 24
Anti-clock wise Anti-clock wise
119 173
370x85 Ø 385 X 90
1 1,4
230 110 230
5 12 8
50 50
2.850 2.800
IP 55 IP 55
146,5 161
147,6 157,5
84 93
GB
) measured in accordance with
WA
L (dB) L (dB)
pA WA
72 84
72 84
S 350 EL
1105800 1105803
345
280
210
24
Anti-clock wise
175
Ø 385 X 90
1,4
230 110
8 14.5
50
2.800
IP 55
161
160
93