Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Fascia
Hitch Shown In Proper Position
Equipment Required: Pliers
Fastener Kit: 24801F
Wrenches: ¾"
Drill Bits: None
5
j
Qty. (4)
½-13 x 1 ¼ Carriage Bolt
k
Qty. (4)
¼ X 1 X 3 Spacer
l
½" Conical Washer
Qty. (4)
1.
Open up hole in frame to allow hardware to be fished into frame, One hole per side. ( See above )
2.
Insert hardware into frame (as per above illustration) using the bolt leaders provided.
3.
Slide frame brackets of hitch between trial pipes and frame of vehicle. Line up holes in frame brackets of hitch with hardware in
frame that was installed in step #2.
4.
Remove bolt leaders from bolts and install the remaining hardware (as per above illustration). See below for torque specs.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
Nissan Altima Coupe 2.5 S & 3.5 SE
Drawbar Kit:
3594
(Sold separately)
Drawbar must be used in the
Rise position only.
3
4
3
4
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 n*m)
Do Not Exceed Lower of Towing Vehicle
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (90.8) Max Tongue Weight
Wiring Access Location: PC3, PC4
Open up these holes to fish hardware into frame
1
2
1
2
3
4
m
Qty. (4)
½-13 Hex Nut
n
½" Bolt Leader
Qty. (4)
Sheet 1 of 3
24801N
Part Numbers:
Manufacturer's Rating or
1
2
1
2
3
4
10-09-15
24801
60877
77172
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24801
Resumen de contenidos para Cequent Performance Products 24801
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3 24801N 10-09-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24801N 10-09-15 Rev. B 2006, 2015 Cequent Performance Products - Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requerimientos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Página 3 de 3 24801N 10-09-15 Rev. B 2006, 2015 Cequent Performance Products - Impreso en México...