Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
rail
Hitch Shown In Proper Position
Equipment Required: Pull wire (Provided)
Fastener Kit: 24798F
Wrenches: 3/4"
Drill Bits: 1"
Kink Pull wire to
keep spacer
independent of bolt
Example of pull wire procedure
Figure 1
j
Qty. (2)
Carriage Bolt 1/2-13 X 1.75 GR5
k
Qty. (3)
Spacer
l
Qty. (3)
Conical Washer
1.
Scrape undercoating from around attachment area large enough for flat washer to fit flush against frame rail.
Drill 1" access hole in bottom of driver's side frame rail between the attachment holes for bolts and spacers.
2.
Feed pull wires with spacer and bolt into frame rail thru 1" drilled hole and out the attachment holes. Place one flat washer on each bolt.
3.
Leave pull wire attached.
4.
Raise hitch into position, feed pull wires thru adjacent holes in the hitch, remove pull wires and attach conical washers and nut finger tight
only (Be careful not to push fastener back into frame rail).
5.
Insert the 1/2-13 X 2.00 carriage bolt and spacer through the tie down hook.
6.
Raise end of hitch into position as shown in Figure 2, attach the conical washer and nut.
7.
Tighten all fasteners.
8.
Paint any exposed metal.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
Fascia
Drawbar Kit:
3593
(Sold separately)
Drawbar must be used in the
RISE position only.
Drill 1" access
hole in bottom of
frame rail
between holes
Frame rail
l
m
Pull wire
k
j
Tighten all 1/2-13 X 1.75 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 1/2-13 X 2.00 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Nissan Versa
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Scrape undercoating from
around both attachment
area large enough for flat
washer to fit flush against
frame rail
n
m
Qty. (3)
Hex Nut 1/2-13
n
Qty. (2)
Flat Washer
o
Qty. (1)
Carriage Bolt 1/2-13 X 2.00
Sheet 1 of 3
24798N
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Tie down
hook
Figure 2
10-09-15
Form F206 Rev A 5605
24798
60875
77170
o
k
l
m
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24798
Resumen de contenidos para Cequent Performance Products 24798
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24798N 10-09-15 Rev. B 2007, 2015 Cequent Performance Products - Printed in Mexico Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24798N 10-09-15 Rev. B 2007, 2015 Cequent Performance Products - Imprimé au Mexique Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 Hoja 3 de 3 24798N 10-09-15 Rev. B 2007, 2015 Cequent Performance Products - Impreso en México Form F206 Rev A 5605...