Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Receiver Shown In Proper Position
Hitch Requires 5/8" Pin and Clip
Equipment Required:
Fastener Kit: 01131-060
Wrenches: 10mm, 18mm, 7/8"
Drill Bits: 1/2"
1
Qty. (6)
Carriage Bolt, 1/2"-13 x 1-3/4"
2
Qty. (4)
Carriage Bolt, 1/2"-13 x 2-1/4"
3
Qty. (6)
Spacer, 1-1/2" x 2" x 1/4"
* Use with optional OEM tow hook.
1.
If present, remove lower fascia under bumper.
2.
If present, remove vehicle tow hooks.
3.
Feed the fasteners shown above through end of frame with pull wire.
4.
Raise hitch into position and attach fasteners and tow hooks as shown above.
5.
If large slot is not present, drill a 1/2" hole using the hitch as a template.
6.
If desired, trim and reinstall the lower fascia. CONSULT VEHICLE OWNER BEFORE TRIMMING.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. Do not cut, weld, or
modify hitch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Chevy/GMC Pickup & Suburban
2500 & 3500 Series – 2WD Only
8600# GVW And Higher (8 Lug Wheels)
Bumper
Lower Fascia
(Optional)
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
500 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
May Need To Be Drilled
On Some Vehicles
OEM Tow Hook (Optional)
4
Qty. (6)
Conical Washer, 1/2"
5
Qty. (6)
Hex Nut, 1/2"
6
Qty. (2)
Pull Wire, 1/2"
Sheet 1 of 3
N65021
Part Numbers:
65021
LB. MAX. WINCH LINE PULL
11-07-05
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65021
Resumen de contenidos para Cequent Towing Products 65021
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65021 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 2 Ne pas découper, souder ni modifier l’attelage. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage Feuille 2 de 3 N65021 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 of 3 N65021 11-07-05 Rev. A 2005 Cequent Towing Products...