Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: K65020
Wrenches: 7/8"
Drill Bits: 1/2"
Narrow Edge
To Outside
Existing Hole
Frame
1
Qty. (6)
Carriage Bolt, 1/2"-13 x 1-3/4"
2
Qty. (2)
Spacer, 1/1/2" x 2" x 1/4"
3
Qty. (6)
Conical Washer, 1/2"
1.
Feed the rearmost fasteners through the end of the frame using pull wire.
2.
Raise receiver into position and install rearmost fasteners.
3.
Using receiver as a template, drill four (4) 1/2" holes.
4.
Feed the remaining fasteners through the end of the frame using pull wire and install remaining fasteners.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
2WD Chevrolet S-10 Blazer (4 Door)
2WD GMC S-15, Sonoma, Jimmy (4 Door)
2WD Isuzu Hombre
Fascia
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
300 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
NOTE: All Fasteners Typical
Both Sides Of Vehicle
Drilled Holes
4
Qty. (6)
Hex Nut, 1/2"
5
Qty. (4)
Spacer, 1" x 2" x 1/4"
6
Qty. (2)
Pull Wire, 1/2"
Sheet 1 of 3
N65020
Part Numbers:
65020
LB. MAX. WINCH LINE PULL
11-07-05
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65020
Resumen de contenidos para Cequent Towing Products 65020
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65020 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N65020 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N65020 11-07-05 Rev. A 2005 Cequent Towing Products...