Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Tape
Fastener Kit: 65063F
Wrenches: 11/16", 17mm
Drill Bits: None
jkkl
Protect Perimeter
of Fascia Opening
j
Qty. (8)
M10 X 1.50 X 60 CL 10.9 Hex Bolt
k
3/8" Conical Washer
Qty. (16)
Note: During the installation, it is recommended to cover the edges of the fascia opening to protect the chrome/paint as shown in Figure 1.
1.
Remove factory tow hooks and fasteners from vehicle, set tow hooks aside and return fasteners to customer.
2.
Before raising hitch into position insert provided fasteners through tow hooks as shown in Figure 2.
3.
Raise hitch into position and align with holes in tow hook mounting bracket.
4.
Raise tow hook into position and insert fasteners through hitch brackets and into the tow hook mounting bracket.
5.
On the reverse side of tow hook mounting bracket install fasteners as shown in Figure 3.
Note: When attaching accessories make sure not to over insert shank into receiver tube, doing so may damage the radiator.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc
Installation Instructions
Dodge RAM 2500/3500
w/ Factory Tow Hook Package
Fascia
Tow Hook
Mounting Bracket
Receiver Tube
Figure 3: Hitch Installation
Figure 1: Fascia Opening
Tighten all M10 fasteners with torque wrench to 53 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
CARGO CAPACITY – Do not exceed
Gross Axle Weight Rating, (GAWR).
9,000lb.
l
Qty. (8)
M10 X 1.50 CL 10 Hex Nut
Sheet 1 of 3
65063N
Part Numbers:
65063
Manufacturer's Rating or
500 LB. or Truck Front
MAXIMUM WINCH LINE PULL
Figure 2: OEM Tow Hook Assembly
1-10-13
Form: F205 Rev C 9-17-2012
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 65063
Resumen de contenidos para Cequent Performance Products 65063
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 1 of 3 65063N 1-10-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc. Hoja 3 de 3 65063N 1-10-13 Rev.