Cequent Performance Products 65061 Instrucciones De Instalación

Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: 65061F
Wrenches: 3/4", 7/8", 15/16"
15mm, if removing air dam
Drill Bits: None
Other Tools: Tape, Cutting
tool for hard plastic fascia.
qpo
mlrknlj
j
Hex Bolt, 1/2"-13 x 6" Gr5
Qty. (2)
k
Flat Washer, 1/2"
Qty. (2)
l
Conical Washer, 1/2"
Qty. (4)
m
Hex Nut, 1/2"
Qty. (2)
n
Qty. (2) Tube, Spacer x 4-1/4"
1. It is necessary to trim a section out of the fascia. See Picture above. Note: For 2011 and newer trucks the air dam must be removed. Use 15mm wrench
to remove (2) nuts holding air dam.
Insert 1/2" x 6" long bolts through conical washers and install through 1" diameter holes on the inside of truck frame rails.
2.
Slide the spacer tubes onto the 1/2" x 6" bolts by inserting them from the outside of truck frame rails.
3.
Secure 1/2" flat washers on outside of truck frame rails using tape as shown in the picture above.
4.
Gently pull bolts back so that the end of the bolts are even with the washers, this is so the hitch can be raised into position.
Position hitch and raise into position being careful not to knock off taped washers on frame. Install fasteners as shown above.
5. Use 5/8" bolt leaders to pull 5/8" carriage bolts into frame slots and through hitch. Square shoulders of bolts must be pulled out to engage with sides
of frame slots. Use access slots on inside of truck frame as shown above to pull 5/8" carriage bolts through. Note: It may be necessary to file slots slightly on
some truck frames to allow bolts to pass through more easily. Or you can pull bolts through end of frame above recovery eyes on 4WD models.
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes.
A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes
with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2012 Cequent Performance Products, Inc.
Front Mounted Receiver Installation Instructions
Ford F-150, 2WD & 4WD Models
All including XL, XLT, STX, FX2, FX4, EcoBoost, Lariat,
King Ranch, Platinum,*SVT Raptor & **Harley-Davidson
Lincoln Mark LT – Mexico only
*Raptor requires front skid-shield modification.
**Harley-Davidson versions may push up on plastic air- dam.
This is a magnified
s
view of a Bolt Leader
s
Fasteners typical both sides of vehicle
CONSULT VEHICLE OWNER BEFORE TRIMMING OR CUTTING FASCIA.
CARGO CAPACITY – Do not exceed
Gross Axle Weight Rating, (GAWR).
9,000lb.
os
Optional to pull
carriage bolts from
end of frame on
4WD trucks.
o
Carriage Bolt, 5/8"-11 X 2" Gr5
Qty. (2)
p
Conical Washer, 5/8"
Qty. (2)
q
Hex Nut, 5/8"
Qty. (2)
r
1.50" x 2.00" Block
Qty. (2)
s
Qty. (2) Pull Wire
Tighten all 5/8" GR5 fasteners with torque wrench to 150 Lb.-Ft (203 N-M).
Sheet 1 of 3 65061N
Part Numbers:
All 4 WD trucks come standard
with recovery eyes,
2WD model trucks do not.
500 LB. or Truck Front
MAXIMUM WINCH LINE PULL
Tape 1/2" flat washer in to
depression around hole on outside of
frame both sides of truck.
Remove
2011 & Up
Trim fascia 1-3/8" from bottom by 3-1/2" wide
for 4WD. 1" up from bottom by 3-1/2" wide for
2WD trucks.
Verify dimensions before trimming fascia.
9-5-12
65061
Rev. A