Cequent Performance Products 65067 Instrucciones De Instalación

Access hole
Frame
Forward of vehicle
Hitch Shown In Proper Position
Equipment Required: Utility Knife, Tape Measure & Marking
Pencil.
Fastener Kit: 65067F
Wrenches: 3/4"
Drill Bits: None
Spacer
Figure 4
Kink Pull wire to keep
spacer independent of bolt
Example of pull wire procedure
1 1 1 1 Qty. (6) Carriage bolt ½-13 X 1.75 GR5
2 2 2 2
Qty. (4) Spacers ¼" X 1.00 X 3.00
3 3 3 3 Qty. (2) Spacer 1/4" X 1.00 X 2.00
It is necessary to either remove lower air dam or trim plastic air dam to install this hitch. See Picture above. CONSULT VEHICLE OWNER BEFORE
REMOVING OR CUTTING PLASTIC AIR DAM.
1. Trim or remove lower air dam. See Figure 2 If cutting, recommend drilling 3/8" at corners to maintain radius for appearance.
2. Feed the coiled end of the pull wire through the bolt attachment hole in the side of the frame and out the access hole. (Note: driver & passenger side use opposite
hole positions) Attach carriage bolt and spacer (item 1 & 2) to the pull wire. Pull the pull wire with fasteners into location through the hole. Leave pull wires
attached. Repeat the same process on the both frame rails. Then push fasteners back into the frame rail leaving the pull wire attached and sticking out. See
Figure 4
3. Feed the coiled end of the pull wire through the forward bolt attachment hole in the bottom of the frame and out the access hole. Attach carriage bolt and spacer
(item 1 & 2) to the pull wire. Leave the pull wire attached.
4. Raise the hitch into position sliding the forward edge of the hitch bracket up over the air dam and into location, feed the pull wires through the slots/holes on the
brackets. Pull the fasteners on the side, back through the frame and bracket for support. Feed conical washer over pull wire, using the washer to hold the bolt in
place remove the pull wires and attach the hex nut. Tighten to hold hitch in place, repeat on all fasteners.
5. Reusing (2) of the pull wires feed remaining carriage bolt and spacer (item 1 & 3) into the access slot on the side of the frame rail and though the rearward hole
on the bottom of the frame. Note: if necessary use a screwdriver to prevent the spacer from spinning. (due to vehicle variation some vehicle have support plates
that will prevent spacers from spinning) Repeat the same process on both frame rails.
6. Torque all fasteners to specifications below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014 Cequent Performance Products, Inc
Front Mounted Receiver
Installation Instructions
Removal of lower air dam or trimming
required. Obtain vehicle owners approval
Fascia
Air Dam
2-5/8"
1-1/2"
3"
Figure 2
Access hole
Forward
Item 3 spacer this
location both sides
Figure 3
Tighten all ½-13 GR 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Ford F-150
before cutting
Access hole
5 5 5 5 4 4 4 4
2 2 2 2
Air Dam Do not use
this hole
2 2 2 2
4 4 4 4
5 5 5 5
Hole location
on opposite side
3 3 3 3
2 2 2 2
6 6 6 6
5 5 5 5
4 4 4 4 Qty. (6)
5 5 5 5
Qty. (6)
6 6 6 6 Qty. (4)
Sheet 1 of 3
Printed in Mexico
CARGO CAPACITY – Do not exceed
500 LB. (227 Kg) or Truck Front
Gross Axle Weight Rating, (GAWR).
9,000 lb.
MAXIMUM WINCH LINE PULL
MAXIMUM WINCH LINE PULL
(4086 Kg)
1 1 1 1
3 3 3 3
2 2 2 2
5 5 5 5
Figure 1
2 2 2 2
4 4 4 4
5 5 5 5
Conical washers ½"
Hex nuts ½-13
Pull wires ½"
65067N 11-24-14
Form: F205 Rev C 9-17-2012
Part Numbers:
65067
Teeth side
against hitch
2 2 2 2 4 4 4 4 5 5 5 5
3 3 3 3
2 2 2 2
5 5 5 5
Rev. B