Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Frame rails
Rear
Figure 1
⑤
1.
Support and lower exhaust: Lower the exhaust by removing (4) rubber hangers, and support the exhaust to prevent it from falling under it's own weight. Spraying a lubricant or soapy
water on the metal hanger rod and the rubber isolator helps removal.
2.
Remove plastic rivets: If present remove the plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a flat screwdriver. Keep for re-installation.
3.
Install fasteners: Feed the coiled end of the pull wire ⑤ through the forward attachment hole in the frame and out the access hole. Feed spacer ② onto the pull wire ⑤ and thread
the carriage bolt ① onto the pull wire ⑤. Pull the pull wire ⑤ with fasteners into location through the hole. Leave pull wire ⑤ attached. Repeat the same process on the both
frame rails. See figure 2. Using the reverse pull wire procedure thread carriage bolt ① onto the pull wire ⑤ and feed it into the access hole on the frame rail then feed the spacer ②
onto the pull wire ⑤ and feed it into the access hole and pull the carriage bolt ① into position through the spacer. Leave the pull wire ⑤ attached. See figure 3.
4.
Install hitch: Raise the hitch above exhaust, feed pull wires ⑤ through the attachment points on hitch brackets. (Gently pull fascia rearward as needed to gain access between the
fascia and exhaust hanger.)
5.
Install fastener: Using the conical washer ③ to hold the bolt in place remove the pull wires ⑤ and attach the hex nut ④. Hand tighten both sides.
6.
Tighten all 1/2 GR5 fasteners to 75 lb-ft. (102 N*M) Note : A universal joint socket may be needed to tighten the rearward fasteners on both sides.
7.
Reinstall exhaust: Raise the exhaust back into position and remove the exhaust support. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps
with reinstalling.
8.
Reinstall plastic rivets if removed in step 2.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2017 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 36601, 06185, CQT36601
Authorized Drawbar Kit:
36051
Drawbar must be used in the RISE position only
FASTENERS TYPICAL ON BOTH SIDES
Access hole
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Printed in Mexico
(Sold Separately)
①
②
Forward attachment
hole
③
④
Sheet 3 of 18
Fastener Kit : 36601F
①
Qty. (4)
Carriage bolt
½-13 x 1.50 GR5
②
Qty. (4)
Spacer
(3022)
.250 x 1 x3
③
Qty. (4)
Conical washer
(02192008)
½''
④
Qty. (4)
Het Nut
½ -13 GR5
⑤
Qty. (4)
Fish wire
½-13
Pull wire procedure
(Conical Washer)
Teeth side
Reverse pull wire procedure
against hitch
Figure 3
36601NP
3-10-17
Figure 2
Rev. A
Publicidad
