User Guide - LEANDER CLASSIC Manual De Instrucciones

USER GUIDE

IMPORTANT!
KEEP FOR FUTURE USE
EN: Baby bed
Pos. 1 The bed base can be set at two different heights.
Make sure that the distance from the mattress to
the top of the bed frame is never less than 300
mm in the top position or 500 mm in the bottom
position. The maximum mattress thickness is
indicated on the bar section of the baby's bed.
By using the original Leander mattress, you are
assured of the correct distance to top edge of the
bed. It is always safest to place the bed base in
the bottom position.
2 As soon as your baby can sit up or stand up on
his/her own, the bed base must be placed in the
bottom position. You must also move the top rails
for the bed base before you can use the bed in the
bottom position.
3 When the baby can crawl out of the baby bed by
himself/herself, one of the bar sections must be
removed to avoid injuries from falling. When using
the top bed-end sections, at least one bar section
must be mounted. Never use the bed when only
the top bed-end sections are mounted.
4 When the baby has developed further, you may
remove the two top bed-end sections and the last
bar section to accommodate the bed to the baby's
needs.
Make sure that medicines, strings, small toys,
1-5
small objects such as coins, etc. are out of the
baby's reach from any position in the bed.
WARNING
• Never place the child's bed by
an open fire or source of strong
heat such as electric heaters, gas
heaters, power points etc. due to
the risk of fire.
• Do not use the child's bed if any
parts are damaged or missing and
only use replacement parts that
are approved by Leander.
• Never leave anything in the child's
bed and never place the child's
bed close to something the child
can stand on, or which may pose
a risk of suffocation or strangula-
tion, such as ribbons, strings on
blinds/ curtains, etc.
4 4
Junior bed
5 Take out the junior box. Replace the sides, and
insert the extra bed base piece as well as the extra
mattress piece. Your Leander junior bed is now
ready for your child.
Cleaning and maintenance
MATTRESS: The mattress cover can be washed at
60°C. Stretch when wet. Do not tumble-dry.
WOODWORK: Can be wiped off with a damp
cloth. Surplus water must be wiped off. The colour
may change when exposed to sunlight.
DAILY USE: Remove the quilt every morning
allowing both bed and quilt to be aerated, cool off
and dry.
Product information
Lacquer complies with the
European standard EN71-3.
DIN EN 716-1:2017+AC:2019, EN 716-2:2017
DESIGN No.: 0002 24076-0001
PATENT No.: PA 20040 1366
Australia: Read the instructions and warnings
about use of mattress in the end of this assembly.
Always follow the assembly instructions in detail
to ensure the safety features of the bed/cot are
not compromised!
Australia: CPN no. 6 of 2005
• Never place more than one
mattress in the child's bed.
• Always use the original Leander
mattress, as it is designed to
fit the bed's curves. The use of
other mattresses can cause gaps
between the mattress and bed
in which the child can become
trapped.
• When assembling the child's bed,
we do not recommend tightening
the screws until the entire bed
is assembled. This will make the
assembly easier.
• After assembly, all fittings and
screws must be checked and
tightened. A poorly assembled
bed and loose parts may lead to
the child trapping a body part or
to clothes (e.g. strings, necklaces,
strings on dummies, etc.) becom-
ing stuck and posing a risk of
strangulation.
• Make sure the cot is placed on a
level and stable surface.
• Remember to keep the Allen key
after assembly. After 2 to 3 weeks
of use, all screws should be
tightened.