Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
FISHWIRE (PROVIDED)
Fastener Kit: 75708F
Fastener Kit: 75708F
Wrenches: T-20, 13mm, 3/4, 7/8
Drill Bits: NONE
TRUNK PAN
5
U-BOLT
HOLES
6
GALVANIC
ISOLATOR
TO THE BOTTOM
OF HORIZONTAL
7 8
MOUNTING TAB.
MOUNTING TAB.
FIGURE 1
1
Qty. (1)
CARRAIGE BOLT – 1/2-13 X 1-1/2" GR 5
2
Qty. (1)
BLOCK – 1 X 2 X 1/4
3
Qty. (3)
WASHER – CONICAL TOOTHED 1/2"
4
Qty. (1)
NUT – 1/2-13
5
Qty. (2)
U-BOLT – 5/16-18
6
6
Qty. (2)
Q
(2)
SPACER – 1-1/2 X 3 X 3/8
SPACER
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
FASCIA
CROSS MEMBER
9
1 1/2 X 3 X 3/8
Audi Q5
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
1 2
SIDE BRACKET
3 4
3
ATTACHMENT
BAR
7
Qty. (4)
WASHER – CONICAL TOOTHED 3/8"
8
Qty. (4)
NUTS – 5/16-18
9
Qty. (2)
HANDLE NUT – 1/2-13
Qty. (2)
BOLT – HEX HEAD 1/2-13 X 1-1/2" GR 5
Qty. (2)
GALVANIC ISOLATOR
11
Sheet 1 of 6
Part Numbers:
Max Gross
Trailer WT (LB)
N/A
4500 (2043 Kg)
Wiring Access Location: SUV1, 2
ACCESS HOLE
SWAY BAR
SWAY BAR
FORWARD
BRACKET
RUBBER
EXHAUST
ISOLATOR
M8
EXHUAST
HANGER
BOLTS
FIGURE 3
75708N
8-12-10
Form: F205 Rev A 5-6-05
75708
87603
44654
Max Tongue
WT (LB)
N/A
450 (204 Kg)
5
FIGURE 2
9
3
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75708
Resumen de contenidos para Cequent Performance Products 75708
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2010 Cequent Performance Products Sheet 1 of 6 75708N 8-12-10 Rev.
-
Página 2: Installation Instructions
Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2010 Cequent Performance Products Sheet 2 of 6 75708N 8-12-10 Rev. - Página 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2010 Cequent Performance Products Feuille 3 de 6...
- Página 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2010 Cequent Performance Products Feuille 4 de 6...
- Página 5 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2010 Cequent Performance Products Hoja 5 de 6 75708N.
-
Página 6: Números De Partes
Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2010 Cequent Performance Products Hoja 6 de 6 75708N. 8-12-10 Rev.