Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Vehicle Frame
Vehicle Fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75549F
Wrenches: 18mm, 19mm
Drill Bits: None
jlmn
Fasteners typical both
Sides of vehicle
j
Qty. (8)
Hex Bolt M12 x 1.75 x 120mm CL8.8
k
Toothed Washer ½"
Qty. (6)
l
Lock Washer ½"
Qty. (2)
Sprinter Van Models:
Remove tie down hook from passenger's side frame rail and return tie down hook and fasteners to vehicle owner.
1.
2.
Raise hitch into position and install fasteners as shown, installing hex bolt and lock washer through round hole in hitch bracket
and hex bolts and toothed washers through oblong slots in hitch bracket, each side.
Sprinter Cab & Chassis Models:
If present, remove wheel chock bracket from driver's side frame rail and retain bracket for reinstallation. Discard bolts.
1.
2.
Raise hitch and wheel chock bracket into position and install fasteners as shown, installing hex bolt and lock washer through
round hole in hitch bracket and hex bolts and toothed washers through oblong slots in hitch bracket, each side.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011, 2012 Cequent Performance Products
Installation Instructions
Mercedes Sprinter (Van and Cab & Chassis)
Dodge Sprinter (Van and Cab & Chassis)
Freightliner Sprinter (Van and Cab & Chassis)
(144" and 170" Wheelbase)
Tighten all M12 x 1.75 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Vehicle Frame
jkmn
m
Qty. (8)
Spacer ¼ x 1 x 2
n
Qty. (8)
Hex Nut M12 x 1.75
Sheet 1 of 3
75549N
Part Numbers:
75549, 44576
87441, 75239 UH
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
7500 (3405 Kg)
750 (341 Kg)
6000 (2724 Kg)
600 (272 Kg)
NOTE:
Unconfirmed reports of vehicles with
30-3/8" frame widths, (measured
outside to outside of frame).
This hitch will not fit a vehicle with a
30-3/8" wide frame measured outside
of frame to outside of frame.
02/24/12
Form: F205 Rev A 5-6-05
Rev. F

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 75549

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75549N 02/24/12 Rev. F 2011, 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuile 2 de 3 75549N 2-24-12 Rev. F 2011, 2012, Cequent Performance Products Form: F205 Rev A 5-6-05...
  • Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2011, 2012 Cequent Performance Products Hoja 3 de 3 75549N 2-24-12 Rev.

Este manual también es adecuado para:

445768744175239 uh