Cequent Performance Products 24884 Instrucciones De Instalación

Hitch Shown In Proper Position
(Sold separately)
Drawbar Kit:
3592
Equipment Required:
Fastener Kit: 24884F
Wrenches: 11/16"
Kink pullwire to keep
spacer independent of bolt
4 Door Accent/Rio
Figure 2.
Reverse pullwire technique
5 Door Accent
Figure 3.
Example of
pullwire procedure
1 1 1 1
Qty. (2) Carriage bolt 7/16-14 X 2.00 GR5
2 2 2 2
Qty. (2) Spacer .13 X .93 X 3.00, Round corners
3 3 3 3
Qty. (3) Conical washer 7/16
4 4 4 4
Qty. (3) Hex nut 7/16-14
Note: Different configurations due to differences in tie down hooks on each make/model.
Note: Due to different configuration of the vehicles there could be extra spacers, item 7 not used.
1. For Kia Rio 2014 to current model, remove the bottom appearance panel on driver side, see Figure 4. Return it to owner.
2. Remove rubber plug from frame rails if present. Return to owner on the 5 door and replace after hitch installation on 4 dr models.
3. On 4 door models using the pullwire method, item 8 (Figure 2), insert items 1 & 2 through forward hole in frame rail as shown.
On 5 door models use the reverse pullwire method (Figure 3) insert items 1 & 2 through hole. Leave pullwires attached.
4. Insert item 5 carriage bolt through item 6 spacer and then through the tie down hook.
5. Feed the pullwires through the slot on the hitch bars.
6. Place item 7 as needed, (1 spacer, 2 spacers, or no spacers), in position on the hitch tie down bracket as shown.
7. Raise the hitch into position being careful not to push the fasteners into the frame rails. Remove pullwire and attach items 3 & 4
as shown.
8. Use remaining fasteners to attach to the tie down hook as shown in Figure 1.
9. Tighten all fasteners to the required torque specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2012, 2015 Cequent Performance Products, Inc. – Printed in Mexico
Installation Instructions
5 Door Accent
fascia
Hyundai Accent 4 Dr. & 5 Dr.
Kia Rio 4 Dr. Sedan
4 Door Accent/Rio
fascia
Drawbar must be used in the
Rise position only.
Figure 4.
Frame rail
8 8 8 8
Hitch bar
3 3 3 3
4 4 4 4
8 8 8 8
Tie down bracket
on hitch
Figure 1.
Note: sort hardware prior to hitch installation to confirm longer 7/16 bolt length for tie down
hook, and small spacers round corners vs. square corners installation
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
Tie
down
hook
7 7 7 7
Tie down
bracket
on hitch 5 Door Accent
Tie down hook
5 5 5 5
Item 7
6 6 6 6
(1) spacer Accent 5 dr
7 7 7 7
(2) spacers Accent 4 dr
No spacer Rio 4 dr
3 3 3 3
4 4 4 4
5 5 5 5
Qty. (1) Carriage bolt 7/16-14 X 2.50 GR5
6 6 6 6
Qty. (1) Spacer .25 X 1.00 X 3.00, Square corners
7 7 7 7
Qty. (2) Spacer .25 X 1.50 X 3.00
8 8 8 8
Qty. (2) Pullwire 7/16
Sheet 1 of 3 24884N
Part Numbers:
24884
60301
77272
24899 UH
Manufacturer's Rating or
4 Door Accent
7 7 7 7
Hitch bar
3 3 3 3
4 4 4 4
10-6--15
Form F206 Rev A 5605
1 1 1 1
2 2 2 2
Rev. C