Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Bumper fascia
Vehicle frame
Exhaust hanger
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24871F
Wrenches: 3/4", 7/8"
Drill Bits: None
Spray lubricant
Fish wire
Vehicle frame
1/2"-13 X 4-1/2" Gr.5 Hex Bolts
Qty. (2)
1
1/4" X 1-1/2" X 3" Blocks
Qty. (2)
2
1/2" Conical washers
Qty. (4)
3
1.
Remove exhaust hangers both sides. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.
Raise hitch into position and insert 4-1/2" bolts and blocks through frame and hitch - both sides. Install conical washers and 1/2"
2.
nuts. Hand tighten only.
3.
Use Fishwire (provide) to install Carriage bolt and block through square hole forward on frame. Keep bolt and block separate
until inside of frame. Install conical washers and 1/2" nuts. Hand tighten only.
Tighten all (4) 1/2" fasteners installed in Step 2 and 3.
4.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011, 2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
Chrysler Sebring, All inc. convertible
Chrysler 200, All inc. convertible
Drawbar Kit:
3594
(Sold separately)
Drawbar must be used in the
Rise position only.
n
o
Vehicle forward
j k
Tighten all 1/2" hex bolts with torque wrench to 40 Lb.-Ft.
Tighten all 1/2" carriage bolts with torque wrench to 75 Lb.-Ft.
Dodge Avenger
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location: (Sebring) PC3 & PC4
Wiring Access Location: (Avenger) PC1 & PC2
Wiring Access Location: (200) PC1 & PC2
l m
1/2" Hex nuts
Qty. (4)
4
1/4" X 1" X 2" Blocks
Qty. (2)
5
1/2"-13 X 1-3/4" Gr.5 Carriage Bolts
Qty. (2)
6
Sheet 1 of 3
24871N
Part Numbers:
24871
60288
77254
Max Gross
Max Tongue
Trailer WT
2000 lb. (908 Kg)
200 lb. (91 Kg)
Vehicle frame
10-07-15
Form: F205 Rev A 5-6-05
WT
Rev. D
Publicidad
Manuales relacionados para Cequent Performance Products 24871
Resumen de contenidos para Cequent Performance Products 24871
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24871N 10-07-15 Rev. D 2011, 2015 Cequent Performance Products - Printed in Mexico Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24871N 10-07-15 Rev. D 2011, 2015 Cequent Performance Products - Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. Sheet 3 of 3 24871N 10-07-15 Rev. D 2011, 2015 Cequent Performance Products - Impreso en México Form: F205 Rev A 5-6-05...