Cequent Performance Products 24873 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: Fish wire (included)
Spray lube
Fastener Kit: 24873F
Wrenches: 7/8, M8, M13
Drill Bits: None
FORWARD
SPARE TIRE LIFT
j
Carriage Bolt – 1/2 – 13 x 4.00 gr5
Qty. (4)
k
Plates – 3-1/16 x 6-3/4 x 3/16
Qty. (2)
l
Washer – Conical toothed 1/2"
Qty. (5)
m
Nut – 1/2 -13
Qty. (5)
n
Carriage Bolt – 1/2 – 13 x 1-3/4 gr5
Qty. (1)
1. Lower spare tire if it has one. Raise vehicle.
2. If spare tire is present, lower spare tire lift by removing (2) M8 screws and (1) M8 nut with m13 socket. Remove rubber plug in frame and fish wire
item 5 and 6 into existing hole. Replace rubber plug and spare tire lift. Leave fish wire on bolt.
3. Remove two fascia mounting screws from fascia supports with m8 wrench.
4. Lower muffler by removing the two pins from the two rubber mounts at the rear of the muffler. It helps if the pins are lubed and the exhaust is gently
pulled rearward.
5. Place plates (item 2) on top of bumper support as shown and install carriage bolts (item 1) Hint; It is easier if the plate is fed in from the center with
the outer bolt already in the plate.
6. Gently pull the fascia down and slide the hitch between the fascia and its support. On turbo models, trim center fin flush and horizontal to the lower
edge of the bumper (see fascia trim diagram above). Put washer (item 7) in place and thread the fish wire through proper hole in bracket.
7. Raise hitch into place as shown and loosely install washers and nuts to bolts (item 1). Pull fish wire with bolt into position, remove the fish wire and
install washer and nut. Install M8 bolt and washer (item 8 and 9) thru bracket and into weld nut in frame.
8. Push hitch forward and tighten all fasteners
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
© 2011, 2014, 2015 Cequent Performance Products -
Installation Instructions
Fiat 500, 500c (convertible),
(Turbo model requires fascia trimming)
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
m l
RUBBER PLUG
FORWARD
ATTACHMENT
HOLE
Tighten all M8 fasteners with torque wrench to 20 Lb.-ft. (27 N*m)
Tighten all 1/2" fasteners with torque wrench to 50 Lb.-ft. (68 N*m)
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
Printed in Mexico
500 Turbo
(Sold separately)
j
BUMPER SUPPORTS
k
j
k
FASCIA SUPPORTS
m l
o
Block – 1 x 3 x 1/4
Qty. (1)
p
Flat Washer – 1/2
Qty. (2)
q
Bolt – M8x1.25 x 30mm
Qty. (1)
r
Washer conical toothed – 3/8"
Qty. (1)
SAE J684.
Sheet 1 of 3 24873N
Part Numbers:
24873, 60289
77255, 24761
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (91 Kg) Max Tongue Weight
Wiring Access Location: PC1, PC2
Fascia Trim Diagram
*Turbo Models Only*
1 1/4"
Area to be trimmed
n o
p
USE ONLY IF
NO SPARE TIRE
LIFT
m
q r
10-07-15
Form F206 Rev A 5605
U-Haul
l
Rev. E