Tabla de contenido
Publicidad
Filter setting
Activation or deactivation of the filter indicators is only
possible with the hood off.
To access the configuration menu, hold pressed T2+T3, once
inside the menu T1 will start to flash.
The default setting is:
grease filter indicator (T2) on, therefore active;
odour filter indicator (T3) off, therefore not activated.
T2 activates/deactivates the grease filter indicator. T3
activates/deactivates the odour filter indicator. To exit the
menu, hold pressed T1 or wait 10''
Filter reset
The hood signals the need for filter maintenance at regular
intervals:
grease filter every 40 hours;
odour filter every 160 hours.
In this case, with the hood off, when the user touches any
button the interface signals two types of needs for a period of
10'':
if T1+T2 flash: grease filter maintenance;
if T1+T3 flash: odour filter maintenance.
During the 10'' it is possible to reset the grease filter by
pressing T1+T2 and to reset the odour filter by pressing
T1+T3. After the reset, the button combinations will flash
rapidly twice. The interface will now work as normal.
Please note:
During the 10", the hood will work normally but without any
visual feedback regarding the speed buttons. If during the 10''
no operations are carried out, the LEDs will stop flashing and
the visual feedback will return to normal.
Maintenance
Cleaning
Clean using ONLY a cloth dampened with neutral liquid
detergent.
DO
NOT
INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Grease filter
Fig. 11
Traps cooking grease particles.
The grease filter must be cleaned once a month using non
aggressive detergents, either by hand or in the dishwasher,
which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolor
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
It absorbs unpleasant odors caused by cooking.
Circular charcoal filter
Apply one on each side as cover to both the shield grids of the
motor impeller, then turn clockwise.
For the disassembly, turn counter-clockwise.
The saturation of the charcoal filter occurs after more or less
prolonged use, depending on the type of cooking and the
CLEAN
WITH
TOOLS
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four months.
The charcoal filter may NOT be washed or regenerated.
Fig. 12a
Washable activated charcoal filter
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Fig. 12b
Replacing lamps
Fig. 10
Disconnect the appliance from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
Replace the old light bulb with the one of the same type as
specified in the feature label or near the light lamp on the
hood.
1.
Using a flat head screwdriver or equivalent tool, carefully
pry loose the light cover.
2. Replace the damaged LED or halogen lamp, with one
having the same characteristics, as specified in the label
features or near the lamp:
LED lamp:For replacement, contact the technical
service.
Halogen lamp: 12V - 20W max - G4 (take care not to
touch them with your hands)
3.
Reinstall the light cover. (it will snap shut).
If the lights do not work, make sure that the lamps are fitted
OR
properly into their housings before you call for technical
assistance.
15
Publicidad
Tabla de contenido
