Cequent Performance Products 75714 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: Lubricant or soapy water, tape
Fastener Kit: 75714F
Wrenches: 18mm, 19mm, 6" Ratchet Extension
6 6
2
Figure 2.
1
Qty. (2) Hex Bolt M12 X 1.25 X 55 CL8.8
2
Qty. (6) Spacer 3/16" X 1.00 X 1.50
3
Qty. (3) Flat Washer 7/16" (Silver)
4
Qty. (3) Lock Washer ½"
1. Lower exhaust system at the rubber isolator. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator
helps removal.
2. Remove the (2) bolts on the tie down on driver's side frame rail. Return fasteners to owner.
3. Tape (3) spacers (item 2), and (5) flat washers (item 6) together for ease of installation.
4 4. Cl Clean threads to assure bolts start. Spray some lubricant into each weldnut. Work bolt in and out until cleaned out. Next get rid of th d t
the lubricant. Use any good household detergent, and flush clean.
5. Raise hitch over exhaust, and install bolt (item 7) and conical washer (item 8) to hold hitch in position.
6. Raise hitch in position on driver's side install the forward bolt, lock washer, flat washer, and spacer, to hold hitch in position.
7. Slide taped spacers (item 2) into position, between tie down and hitch bracket. Install spacer, flat washer, lock washer and hex
bolt (item 1). Do not tighten.
8. Slide taped washers (item 6) into position, between tie down and hitch bracket. Install spacer, flat washer, lock washer and hex
bolt (item 1). Hand tighten fastener and orient spacers as shown Figure 2.
9. Install remaining fasteners to passenger's side frame rail.
10 Tighten all fasteners to called out torque specification 10. Tighten all fasteners to called-out torque specification.
11. Reattach exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011 Cequent Performance Products
Installation Instructions
Fascia
Frame rail
6
2
2
3
4
Orientation of
spacers driver's
side bracket
b lt t t S l b i
Tighten all M12 CL8.8 fasteners with torque wrench to 42 Lb.-Ft. (57N*M)
Nissan Quest
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or N
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 1 & 2
Tie down
2
3
4
7
1
Forward
Figure 1.
6
Qty. (5)
7
Qty. (4)
8
Qty.(4)
9
t i t h ld t W k b lt i
Sheet 1 of 3
g V
Max Gross
Trailer WT (LB)
Not For Use With Spring Bars
3500 (1589 Kg)
Forward hole F d h l
Flat washers (5)
Spacers (3) install
Trunk pan and
exhaust not shown
Flat washer 1/2" (Black)
Hex Bolt M12 X 1.25 X 45 CL8.8
Conical Washer 1/2" (Yellow)
d t til l
75714N 6-3-11
Part Numbers:
75714
87609
44663
75228
U-Haul
g
Max Tongue
WT (LB)
525 (239 Kg)
Frame rail
Existing
weldnuts
8
7
d t N t t id f
Rev. B
Form: F205 Rev A 5-6-05