Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75717F
Wrenches: 16mm
Drill Bits: NONE
j k
NOTE: If additional exhaust clearance is required, bend exhaust hanger rod appropriately
j
Hex Bolt – M10 x 1.25 x 30mm CL 10.9
Qty. (4)
1. Raise vehicle with hoist or ramps for access to underside.
2. While supporting exhaust remove rear hangers and lower exhaust until hitch can be positioned over the
muffler tips and into position aligning slots in hitch with existing weld nuts in the bottom of frame.
3. Loosely install the M10 hex bolts with conical washers, (4) four places, as shown.
4. Tighten all M10 CL10.9 fasteners with torque wrench.
5. Reinstall rear hangers for exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2011, 2012, 2013 Cequent Performance Products, Inc.
Printed in México
Installation Instructions
HYUNDAI TUCSON
KIA SPORTAGE
FASCIA
FRAME
EXSISTING WELD NUTS
BOTH SIDES
KIA SPORTAGE
Tighten all M10 CL 10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 n*m)
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2 (Tucson)
k
Conical Washer – 3/8"
Qty. (4)
Sheet 1 of 3
75717N
Part Numbers:
75717
87612
44666
75188
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5250 (1816 Kg)
525 (182Kg)
3500 (1589Kg)
525 (159Kg)
SUV1, SUV5 (Sportage)
HYUNDAI TUCSON
10-24-13
Form F206 Rev A 5605
U-HAUL
Max Tongue
WT (LB)
j k
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 75717
Resumen de contenidos para Cequent Performance Products 75717
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2011, 2012, 2013 Cequent Performance Products, Inc. Sheet 1 of 3 75717N 10-24-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2011, 2012, 2013 Cequent Performance Products, Inc. Feuille 2 de 3 75717N 10-24-13 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del Estado de Nueva York, V.E.S.C. Regulación V-5 d SAE J684. © 2011, 2012, 2013 Cequent Performance Products, Inc. Hoja 3 de 3 75717N 10-24-13 Rev.