Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: wire pulls (provided)
Fastener Kit: 75716F
Wrenches: 11/16", 7/8"
Drill Bits: None
1 1 1 1 2 2 2 2
BUMPER
FASTENERS ARE THE
SAME FROM SIDE TO SIDE
1 1 1 1
Qty. (2)
Bolt carriage 7/16-14 x 1-1/2" Gr 5
2 2 2 2
Qty. (2)
Block – 1 x 2 x 3/16"
3 3 3 3
Qty. (2)
Washer conical – 7/16"
4 4 4 4
Qty. (2)
Nut – 7/16"-14
1.
Lower the spare tire from the underside of the vehicle.
2.
Using the 7/16 wire pulls, insert the 7/16 Carriage bolts and 3/16 x 1" x 2" blocks through the end of the vehicle bumper structure
and through the existing holes. Keep wire pulls attached to bolts until hitch is in position.
3.
Raise hitch into position and loosely install 7/16 Conical toothed washers and 7/16 Hex nuts as shown above.
4.
Using the ½ wire pull insert the ½ Carriage bolts and ¼ X 1" X 3" Blocks through the side holes in the vehicle frame structure to
the existing holes in the vehicle frame rails and through the receiver.
5.
Install ½ Conical toothed washers and ½ hex nuts.
6.
Tighten all fasteners to the required torque specifications.
7.
Raise spare tire back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2011, 2012 Cequent Performance Products
Installation Instructions
Subaru Tribeca
4 4 4 4
3 3 3 3
Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 1/2-13 Gr5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 8
5 5 5 5 6 6 6 6
7 7 7 7 8 8 8 8
5 5 5 5
Qty. (2)
Bolt carriage 1/2-13 x 2 Gr 5
6 6 6 6
Qty. (2)
Block – 1 x 3 x 1/4"
7 7 7 7
Qty. (2)
Washer conical – 1/2"
8 8 8 8
Qty. (2)
Nut – 1/2"-13
Sheet 1 of 3
75716N
Part Numbers:
75716
87611
44665
75243
U-Haul
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5250 (2384 kg)
525 (238 kg)
3500 (1589 kg)
525 (238 kg)
FRAME
1-4-12
Rev. B
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 75716
Resumen de contenidos para Cequent Performance Products 75716
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75716N 1-4-12 Rev. B 2011, 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. de l’état de New York concernant les spécifications en matière de sécurité des systèmes et dispositifs d’attelage. © 2011, 2012 Cequent Performance Products, Inc Feuillet 2 sur 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del Estado de Nueva York, V.E.S.C. Regulación V-5 d SAE J684. Página 3 de 3 75716N 1-4-12 Rev. B 2011, 2012 Cequent Performance Products Form: F205 Rev A 5-6-05...