Ordering Information - smith&nephew SPIDER2 Modo De Empleo

English
To Clean SPIDER2
1. Remove all single use components and accessories. Discard single use components.
Refer to cleaning and sterilization instructions for accessories: 79-99-04 Cleaning and
Sterilization Instructions.
2. Wipe entire SPIDER2 with mild detergent / disinfectant, taking care to avoid fluid entry
into Switch Drape or Foot Pedal Receptacles.
3. Wipe battery with mild detergent / disinfectant.
4. Dry SPIDER2 with a cloth or allow to air dry.
5. DO NOT immerse any portion of SPIDER2 in liquid. If moisture enters the equipment it
can cause corrosion, and damage electrical and/or mechanical components.
6. DO NOT autoclave SPIDER2.
7. DO NOT use ethylene oxide to sterilize SPIDER2.
Storage
1. Turn OFF and DEPRESSURIZE SPIDER2 by disconnecting the Foot Pedal and/or Switch
Drape and pressing the Power Switch to the DEPRESSURIZE Position for 1 second (Figure
2). The Power Switch will then return to the OFF/STORAGE Position.
2. Always depressurize and then turn off the SPIDER2 when not in use. Failure to do so will
reduce the life expectancy of the device.
Maintenance
Only trained individuals should perform maintenance on SPIDER2. Contact Smith &
Nephew to determine which maintenance can be performed on site.
SPIDER2 Specifications*
Model REF 72203299 SPIDER2
Length: 1495 mm Width: 180 mm
Size (fully extended)
Height: 200 mm
Weight 30 lbs [13.6 kg] (with battery installed)
CSA International
CAN/CSA-C22.2 No.601.1-M90
Approval
UL 60601-1
IEC 60601-1
Equipment type Type B Applied Part
Power Supply Internally Powered 24V
Battery Type NiCd 24V 1.8Ah
Battery Model REF 72203301 SPIDER2 Battery Pack
Enclosure Protection IPX1 Drip-proof equipment
Environmental Conditions Operation
Temperature 10°C - 40°C
Relative Humidity 30% - 75%
Atmospheric Pressure 70kPa - 106kPa
EU: Not for general waste
Disposal
Contact Smith & Nephew for appropriate methods of
disposal.
* Specifications are approximate and may vary from unit to unit or as a result of power
supply fluctuations
6
126-99-01 Rev. C
15A
Storage & Transportation
-40°C - 70°C
10% - 100%
50kPa - 106kPa
SPIDER2 Battery Charger Specification
Intertek
CAN/CSA Std C22.2 No. 60950-1
Approval
UL 60950-1
IEC 60950-1
Power supply 100-240 VAC, 50-60 Hz, Max 0.9 A

Ordering Information

SPIDER2 Accessories*
REF
72203301
7210570
7210749
7210577
7210571
7210576
7210572
72200660
72202932
72203235
72203236
72203239
* SPIDER2 is packaged with:
(1) SPIDER2
(1) SPIDER2 Battery Pack
(1) SPIDER2 Battery Charger
(3) Power Cords (Type A - NEMA 1-15, Type C - CEE 7/16 Europlug, Type G - BS 1363).
Contact Smith & Nephew for additional power cords, if required.
Stabilization Kits
72203833
7210573
7210574
72201550
72201551
72201552
72202931
72203238
72203300
Warranty
This product has a standard 12-month parts and labor warranty against manufacturing
defects.
For Further Information
If further information on this product is needed, contact Smith & Nephew Customer Service
at +1 800 343 5717 in the U.S., or an authorized representative.
SPIDER2 Limb Positioner
Description
SPIDER2 Battery Pack
Piggy Back
90° Connector
Traction Accessory
Shoulder Connection Bar
Lateral Shoulder Connection Bar
Elbow Connection Bar
Wrist Arthroscopy Accessory
Ankle Arthroscopy Accessory
SPIDER Leg Accessory (Left)
SPIDER Leg Accessory (Right)
3D SPIDER Connector
SPIDER2 Shoulder Stabilization Kit
Shoulder Stabilization Kit
Elbow Stabilization Kit
Small Wrist Stabilization Kit
Medium Wrist Stabilization Kit
Large Wrist Stabilization Kit
Ankle Stabilization Kit
Leg Stabilization Kit
Switch Drape
Instructions for Use