Personal Safety - Speedaire 2Z365G Manual De Instrucciones De Operación

Speedaire Operating Instructions
Speedaire
Conventional Spray Guns
General Safety Information
E
(Continued)
N
G
•
Always work in a clean environment.
L
To avoid injury or damage to the
I
workpiece, do not aim the spray gun at
S
any dust or debris.
H
•
Keep visitors away and NEVER allow
children or pets in the work area.

PERSONAL SAFETy

•
Use a face mask/respirator,
non-skid shoes, and
protective clothing when
spraying. Always spray in
a well ventilated area to
prevent health and fire hazards. Refer to
Material Safety Data Sheets (MSDS) of
spray material for details.
•
Always wear eye
protection
•
Never use oxygen, carbon dioxide,
combustible gases or any bottled gas
as an air source for the spray gun.
Such gases are capable of explosion
and serious injury to persons.
•
Do not misuse this product. Excessive
exposure to vibration, work in
awkward positions, and repetitive
work motions can cause injury to
hands and arms. Stop using any tool
if discomfort, numbness, tingling, or
pain occur, and consult a physician.
•
Never aim or spray at yourself or
anyone else or serious injury could
occur.
•
Do not spray acids, corrosive
materials, toxic chemicals, fertilizers
or pesticides. Using these materials
could result in death or serious injury.
Pressure Feed -
®
•
When spraying and cleaning, always
follow the instructions and safety
precautions provided by the material
manufacturer (Refer to MSDS).
•
Do not overreach. Keep
proper footing and balance
at all times. Proper footing
and balance enables better
control of the spray gun in
unexpected situations.
•
Stay alert. Watch what you are doing
and use common sense when operating
the spray gun. Do not use the spray
gun while tired or under the influence
of drugs, alcohol, or medication. A
moment of inattention while operating
the spray gun increases the risk of
injury to persons.
TOOL USE AND CARE
•
Do not use pressure that
exceeds operating pressure
of the spray gun or any of the
parts (hoses, fittings, etc.) in
the painting system.
•
Over pressurizing the spray gun is
able to result in bursting, abnormal
operation, breakage of the spray gun
or serious injury to persons.
•
Always verify prior to using the spray
gun that the air source has been
adjusted to the rated air pressure or
within the rated air-pressure range.
•
Check for misalignment or binding of
moving parts, breakage of parts, and
any other condition that affects the
spray gun's operation. If damaged, have
the spray gun serviced before using.
Many accidents are caused by poorly
maintained spray guns. There is a risk of
bursting if the spray gun is damaged.
2
•
Avoid unintentional starting. Be sure
the trigger is off before connecting to
the air supply. Do not carry the spray
gun with your finger on the trigger or
connect the spray gun to the air supply
with the trigger on.
•
Disconnect the spray gun from the air
source before, changing accessories,
cleaning, servicing or storing the
spray gun. Such preventive safety
measures reduce the risk of starting
the spray gun unintentionally.
•
Failure to install appropriate water/
oil removal equipment may result in
damage to machinery or workpiece.
•
Always use a pressure regulator on
the air supply to the spray gun.
Introduction
The spray gun is a vital link in any
finishing application. In addition to
operating the spray gun properly,
techniques of surface preparation and
paint preparation must be understood.
These instructions will explain the
differences among various spray
technologies and serve as a guide in
the proper operation and techniques of
spray painting. Refer to the Replacement
Parts Manual for model specific
information.
SPRAy GUN TERmS
Atomization – Conversion of bulk
liquid to spray droplets (mist).
Bleeder – In this mode, air passes
continuously through the gun whether
spraying or not. This mode is generally
used when the air is supplied by a
continuously running compressor that
does not have a tank.