Tabla de contenido
Publicidad
Enlaces rápidos
5PD PREMIERE PULL-DOWN SHELVING SYSTEM
Component
Description
No.
A
Base Left
Base Right
B
TOOLS REQUIRED:
C
Left kit
Right kit
D
E
Handle
F
Wire Basket
3
Synchronization
G
H
Bar
32
Large drawer
I
J
Small drawer
Top bin
K
(2mm)
Long divider
L
M
Short divider
1
A
#2
4
(6mm)
1
4
C
(6mm)
#2
ESTIMATED ASSEMBLY TIME:
D
45 MIN
CARE AND MAINTENANCE:
Clean with a damp cloth
and wipe parts dry. Keep all
chemicals away from gas spring
piston rod.
E
Qty
1
1
1
1
1
2
1
F
1
1
2
2
1
2
B
G
H
PART LIST:
I
A
B
D
F
(1) Left-mount bracket
bracket
, (1) Left-side frame
(B)
(1) Right-side frame
(2) Wire basket
, (1) Synchronization bar
(F)
INSTALLATION INSTRUCTIONS: 5PD SERIES PULL DOWN
J
K
L
M
1
C
1/4"x1-1/4"
Screws (4)
E
5
G
Wood
Screws (10)
, (1) Right-mount
(A)
,
(C)
, (1)Handle
,
(D)
(E)
(G)
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
No.
1
2
3
4
5
6
7
8
1
2
3
4
2
3
4
Cap Nut
Washer
(4)
(4)
6
7
8
M4x6
M5x12
Screws (4)
Flat head
Screws (4)
Logo
Cover (4)
Fittings
Description
1-1/4" x 1/4" Screw
1/4" Cap Nut
Washer
M5x12 (Pan Haed Screw
Wood screw
M4x6 Screw
M5x12 (flat head Screw)
Logo Cover
5
6
7
8
M5x12
Pan-head
screws (4)
I-5PD-TRI-0116
Publicidad
Tabla de contenido
Manuales relacionados para Rev-A-Shelf 5PD PREMIERE
Resumen de contenidos para Rev-A-Shelf 5PD PREMIERE
- Página 1 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 5PD PREMIERE PULL-DOWN SHELVING SYSTEM Component Fittings Description Description Base Left 1-1/4" x 1/4" Screw Base Right TOOLS REQUIRED: 1/4" Cap Nut Left kit Washer Right kit M5x12 (Pan Haed Screw...
-
Página 2: Bottom Mounting
When side mounting into a Face Frame cabinet, depending on your cabinet construction such as, Face Frame width, hinge #5 Wood Screws style, and location, a scab board may be required. (2mm) Customer Service: 800-626-1126 | rev-a-shelf.com... - Página 3 Assembly STEP 3 FIG. FIG. Attach the two wire baskets to the side frames using qty (8) M5x8 pan head machine screws as shown in figure 3. Note: Screws may already be attached to brackets. Attach the handle to the side frames using qty (2) M5x8 pan head machine screws as shown in figure 4.
- Página 4 The unit should return inside the cabinet on its own power. If it is heavily loaded, you may need to assist with the return by lifting the handle. 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 Customer Service: 800-626-1126 | rev-a-shelf.com...
- Página 5 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN INSTRUCTIONS D’INSTALLATION SISTEMA PREMIERE DE REPISAS PARA BAJAR 5PD 5PD PREMIER DE TABLETTES ESCAMOTABLES Component Fittings Description Description Base Left 1-1/4" x 1/4" Screw HERRAMIENTAS REQUERIDAS: Base Right 1/4"...
-
Página 6: Montaje Inferior
(2mm) armoire, telles que la largeur du cadrage avant, type de charnière, et emplacement, un panneau de renforcement supplémentaire peut être nécessaire. Customer Service: 800-626-1126 | rev-a-shelf.com... -
Página 7: Ensamble
Ensamble PASO 3 Assemblage ÉTAPE 3 FIG. FIG. Sujete las dos canastas de alambre a los lados del marco utilizando 8 tornillos de máquina del número M5x8 como se muestra en la figura 3. Nota: Los tornillos deben ya estar sujetos a los soportes. -
Página 8: Operación
L’unité devrait revenir par elle-même à l’intérieur de l’armoire. Si elle est très chargée, vous devrez peut-être aider le retour en soulevant la poignée. 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 Customer Service: 800-626-1126 | rev-a-shelf.com...