Publicidad
Position so that the hole is at the center of
the battery holders.
2.5. Fold paper battery holder as shown and
secure corners with double-sided tape (thin)
⑭.
2.6. As shown, insert one connecting plug from
each of the two plastic conductive wires
into the battery holders in the positions
indicated in the diagram. Insert one by one.
2.7. Insert the plugs at the other end of the
plastic conductive wires into the space in
the center of the battery holders. Pull the
plugs out through the paper battery case.
2.8. After passing through both plugs close the
lid of the battery holder.
2.9. Use a 1cm x 3 cm length of double-sided
tape (thick) ⑮ to attach switch ⑥ to Paper
battery holder in the position indicated in
the diagram.
2.10. Insert two plugs into the switch metal
fittings. Insert one by one.
2.11. Paper battery case is complete.
3. Assembly of motor section Prepare ④ ⑤ ⑦
3. Assembly of motor section Prepare ④ ⑤ ⑦
⑨ ⑩ ⑫ ⑬ ⑮
⑨ ⑩ ⑫ ⑬ ⑮
3.1. Connect plugs to the red and blue
conductive wires of motor ⑦.
3.2. Mountain fold all the folding lines of paper
joint part ④.
3.3. Using double-sided tape (thick) ⑮, attach
and secure the motor in the center hole of
paper joint part.
3.4. Wrap a rubber band ⑫ around the tabs
to secure the motor. Wrap rubber band
around twice.
3.5. Affix propeller retaining part (lower) ⑩ onto
the pinion gear of the motor. Firmly hold the
back of the motor. Finished part
3.6. Bend paper propeller ⑤ flaps forward along
the four lines as shown.
3.7. Attach propeller and propeller retaining part
(upper) ⑨ to propeller retaining part (lower)
⑩. Firmly hold the back of the motor.
3.8. Cut six 1.5 x 1.5 cm lengths of double-sided
tape (thick) ⑮ and stick on the positions
indicated in the picture.
3.9. Motor section is complete.
4. Cutting the plastic bottle
4. Cutting the plastic bottle
4.1. Make a cut to your plastic bottle with the
box cutter as shown. *The position is
approx. 100 mm from the top of the plastic
bottle.
4.2. Insert the blade of the scissors into the
cut you made with the box cutter.Cut off
the upper part of the plastic bottle. *Cut
carefully so the section will be straight and
parallel.
4.3. The plastic bottle body is complete.
5. Handle assembly
5. Handle assembly
5.1. Fold paper handle ③ as shown and apply
double-sided tape (thin) ⑭ to tabs as
shown.
5.2. Apply double-sided tape (thin) to the
opposite side.
5.3. The handle is complete.
6. Assembly of all sections
6. Assembly of all sections
6.1. Attach motor section assembled in Step
2 to battery holder assembled in Step 3
using double-sided tape (thin) ⑭. Align
with the white frame and stick into position
using double-sided tape (thin) ⑭. Finished
section.
6.2. Pass the red and blue conductive wires
from the motor through the hole as shown
in the picture. Pass both wires through.
6.3. Turn box over and open lid of battery
holder. Insert plugs connected to red and
blue conductive wires into battery holders.
Blue conductive wire Negative terminal (-).
Red conductive wire Positive terminal (+).
6.4. Using double-sided tape (thick) ⑮, attach
upper area of motor section to plastic bottle
at the three points shown. Attach in order of
①, ② and ③. Align with the upper side of
the plastic bottle and the motor section.
6.5. Using double-sided tape (thick) ⑮, attach
lower area of motor section to plastic bottle
at the three points shown. Front view.
Attach in order of ①, ② and ③. Attach in
order of ①, ② and ③. If the plastic bottle is
thin, valley fold and stick double-sided tape
(thick) ⑮ at the area indicated with arrows
in the diagram.
6.6. Fold the paper body ② as shown.Valley
fold at the two places with arrows and
mountain fold along other parts.
6.7. Attach Paper body on one side using
double-sided tape (thin) ⑭ to the side of
battery holder as shown.
6.8. Use double-sided tape (thin) ⑭ to attach
tabs at four locations on the plastic bottle.
Stick double-sided tape (thin) ⑭ on the
inner side.
6.9. Stick 1 x 1.5 cm lengths of double-sided
tape (thick) ⑮ to the handle assembled
in Step 5 at the positions indicated in the
diagram.
6.10. Use Double-sided tape (thick) ⑮ to
attach the handle to the main body at the
position shown in the picture.
6.11. Completed item.
7. Preparations prior to the experiments
7. Preparations prior to the experiments
Place batteries as shown. Place batteries with
the +/- terminals in the correct position. Red
should be the (+) and blue the (-).
8. How it works
8. How it works
When you turn on the switch, the rotating
propeller will expel the air inside the plastic
bottle to reduce the amount of air inside.
As the amount of air decreases, the air pressure
inside the plastic bottle also decreases.
Air has a tendency of flowing from where the
pressure is high to low.
This tendency makes the plastic bottle with low
air pressure suck in air from outside which has
a high pressure, together with dust and debris.
9. How to use
9. How to use
Vacuum up the dust:
Turn the switch at the tail-end of the body ON.
Bring the open end of the plastic bottle close to
dust and it will be sucked up, whirling into the
plastic bottle.
Throw away the dust:
Turn the switch on the tail-end of the body OFF.
Position the open end side of the plastic bottle
cleaner downward and the dust will come out of
the bottle.
10. Troubleshooting
10. Troubleshooting
Propeller does not rotate properly:
-
Read the instructions again and check the
wiring carefully.
-
Check the propeller is not touching the body
or the plastic bottle.
Does not vacuum up any dust:
-
Read the instructions again and check
P9
the propeller flaps are bent in the proper
direction.
-
Place batteries with the +/- terminals in the
correct position.
-
This vacuum cleaner will not be able to
vacuum up heavy objects or anything bigger
than its bottle top diameter.
(FR)
INSTRUCTIONS POUR LES ENFANTS DE 8
ANS ET PLUS :
Avant de commencer :
Avant de commencer :
-
Vérifier que la boîte contienne toutes les
pièces.
-
Bien lire les instructions avant le montage.
-
Manipuler les pièces en carton avec soin
pour qu'elles ne se déchirent pas.
Tu auras besoin de :
Tu auras besoin de :
-
1 Bouteille cylindrique en plastique d'environ
65-70 mm de diamètre et de 500 ml.
-
Ciseaux
-
Cutter
-
2 Piles AA
1. Description des pièces :
1. Description des pièces :
1.1. Boîtier des piles en papier
1.2. Corps en papier
1.3. Poignée en papier
1.4. Pièce de jonction en papier
1.5. Hélice en papier
1.6. Interrupteur
1.7. Moteur
1.8. 2 Boîtiers de piles
1.9. Fixation supérieure de l'hélice A
1.10. Fixation supérieure de l'hélice B
1.11. Câble
1.12. Élastique
1.13. 6 Fiches de branchement
1.14. Ruban adhésif épais
1.15. Ruban adhésif mince
2. Montage du boîtier de piles
2. Montage du boîtier de piles
2.1. Couper le câble (11) en deux et en dénuder
les extrémités sur 3 cm.
2.2. Introduire les câbles dans les fiches de
branchement.
2.3. Couper deux morceaux de ruban adhésif
de 1x3 cm (11). Connecter les deux boîtiers
entre eux et appliquer du ruban adhésif à
l'arrière.
2.4. Avec du ruban double face, coller les deux
boîtiers de piles dans la boîte. Attention à
leur position. Voir illustration.
2.5. Plier la pièce en papier et la monter avec
de la colle.
2.6. Insérer dans les boîtiers une des fiches qui
sont connectées aux câbles jaunes.
2.7. Passer les fiches libres par les boîtiers de
piles et tirer dessus à travers le trou de la
boîte en papier.
2.8. Fermer le couvercle.
2.9. Couper un morceau de ruban adhésif de
1x3 cm et coller l'interrupteur à la boîte en
papier.
2.10. Insérer les fiches encore libres dans
l'interrupteur.
2.11. Terminé.
3. Montage de la section du moteur
3. Montage de la section du moteur
3.1. Insérer les câbles dans les fiches de
connexion comme indiqué.
3.2. Plier et monter
3.3. Placer le moteur au centre et le fixer avec
Publicidad
