Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
USING YOUR DYSON MACHINE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
•
Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
•
Ensure the machine remains upright in use. Dirt and debris may be released if it
is turned upside down.
•
Do not operate while checking for blockages as doing so could result in
personal injury
•
For domestic indoor and car use only. Do not use it while the car is in motion or
while driving.
•
To operate the boost mode, hold the trigger down and press the boost button.
The 'boost' button will light up.
•
To switch off boost mode, hold the trigger down and press the boost button
again. Note: The machine will retain the last used mode. So if you use it in boost
mode and do not disengage it, the machine will operate in boost mode when it is
next used until you depress the boost button to disengage it.
•
To watch a short online video visit:
www.dyson.com/dc58gettingstarted
CARPETS OR HARD FLOORS
•
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
•
Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
LOOKING AFTER YOUR DYSON MACHINE
•
Do not carry out any maintenance or repair work other than that shown and
described in this Dyson Operating Manual, or advised by the Dyson Helpline.
•
Only use parts recommended by Dyson. If you do not this will invalidate your
warranty.
•
Store the machine indoors. Do not use or store it below 37.4°F (3°C). Ensure the
machine is at room temperature before operating.
•
Clean the machine only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the machine.
VACUUMING
•
Do not use without the clear bin and filter in place.
•
Fine dirt such as flour should only be vacuumed in very small amounts.
•
Do not use the machine to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the machine.
•
When vacuuming, certain carpets may generate small static charges in the clear
bin. These are harmless and are not associated with the mains electricity supply.
To minimise any effect from this, do not put your hand or insert any object into
the clear bin unless you have first emptied it. Clean the clear bin with a damp
cloth only. (See 'Cleaning the clear bin'.)
•
Use extra care when cleaning on stairs.
•
Do not rest the machine on chairs, tables, etc.
•
Do not press down on the nozzle with excessive force when using the machine as
this may cause damage.
•
Do not leave the cleaner head in one place on delicate floors.
•
On waxed floors the movement of the cleaner head may create an uneven luster.
If this happens, wipe with a damp cloth, polish the area with wax, and wait for
it to dry.
EMPTYING THE CLEAR BIN
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•
Ensure the machine is disconnected from the charger before emptying the clear
bin. Be careful not to pull the 'ON' trigger.
•
To release the dirt, push the red button by the clear bin. Press once to open the
bin base. Press a second time to release the clear bin from the main body of the
machine.
•
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
•
Remove the clear bin carefully from the bag.
•
Seal the bag tightly, dispose as normal.
•
Close the clear bin base so it clicks into place and is secure.
CLEANING THE CLEAR BIN
•
Ensure the machine is disconnected from the charger before removing the clear
bin. Be careful not to pull the 'ON' trigger.
•
Push the red button by the clear bin. Press once to open the bin base. Press a
second time to release the clear bin from the main body of the machine.
•
Remove the clear bin carefully.
•
Clean the clear bin with a damp cloth only.
•
Do not use detergents, polishes or air fresheners to clean the clear bin.
•
Do not put the clear bin in a dishwasher.
•
Clean the cyclone shroud with the brush on the combination tool to remove lint
and dust.
•
Ensure the clear bin is completely dry before replacing.
•
To replace the clear bin, push the clear bin up and in to the main body of the
machine. It will click into place.
•
Close the clear bin base so it clicks into place and is secure.
WASHING YOUR FILTER
•
Ensure the machine is disconnected from the charger before removing the filter.
Be careful not to pull the 'ON' trigger.
•
Your machine has one washable filter, located as shown.
8
•
To remove the filter, lift it out of the top of the machine.
•
Check and wash the filter regularly according to instructions to maintain
performance.
•
The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'HIGH CONSTANT SUCTION' mode.
•
Wash the filter with cold water only.
•
Run water over the outside of the filter until the water runs clear.
•
Squeeze and twist with both hands to make sure the excess water is removed.
•
Lay the filter on its side to dry. Leave to dry completely for a minimum of
24 hours.
•
Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
•
To refit, place the dry filter back into the top of the machine. Make sure it is
seated properly.
•
To watch a short online video visit:
www.dyson.com/dc58filterwash
LOOKING FOR BLOCKAGES
•
Ensure the machine is disconnected from the charger before looking for
blockages. Be careful not to pull the 'ON' trigger.
•
Do not operate while checking for blockages as doing so could result in
personal injury
•
Beware of sharp objects when checking for blockages.
•
Refit all parts securely before using.
•
Clearing blockages is not covered by your warranty.
BLOCKAGES – THERMAL CUT-OUT
•
This machine is fitted with an automatically resetting thermal cut-out.
•
Large items may block the tools or nozzle. If any part becomes blocked the
machine may overheat and automatically cut-out.
•
Leave to cool down for 1-2 hours before checking the filter or for blockages.
•
Ensure the machine is disconnected from the charger before looking for
blockages. Failure to do so could result in personal injury.
•
Clear any blockage before restarting.
•
Refit all parts securely before using.
•
Clearing blockages is not covered by your warranty.
DIAGNOSTICS - MAIN BODY
When in use, trigger pressed:
Solid blue: Boost 'ON'.
Light off: Powerful suction.
Flashing blue: Low battery warning.
Fast flashing blue: No power, temporary
fault (e.g. check filter or for blockages).
DIAGNOSTICS – BATTERY
when in use, trigger pressed:
Solid blue: 'ON'.
Flashing blue: No power,
charge battery.
Flashing amber: No power, temporary
fault (e.g. too hot/cold).
Solid amber: Fault, if persists
contact Dyson helpline.
Flashing red: Fault (contact
Dyson helpline).
Publicidad
Tabla de contenido
