X-LITE X-1004 Seguridad E Instrucciones página 11

WARNING
- Use the special slider to activate/deactivate the VPS; do not deactivate the VPS by handling it directly.
- The VPS can only be used during the day and under the environmental conditions described before.
- At night and/or in conditions of poor visibility, the VPS must be deactivated.
- Always check that the VPS is properly positioned according to different weather/environmental conditions
and/or the above-mentioned recommendations for use.
- We recommend using the VPS only and solely together with the approved standard visor, which has a
transmittance value greater than 80%.
- The VPS does not replace the protection guaranteed by the visor.
- Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or
anomalous wear on it every time it is activated.
- As for VPS and visor maintenance and cleaning operations, please refer to the appropriate section in the
- The VPS scratch-resistant/fog-resistant treatment highly reduces fogging. Protracted periods of adverse
weather and/or environmental conditions might cause fogging and/or formation of condensation on the VPS,
which entails a reduction of visibility and/or sharpness of vision: in this case, deactivate the VPS.
- In case of rain, the direct contact of raindrops with the scratch-resistant/fog-resistant treated VPS quickly
reduces sharpness of vision, thus causing scarce visibility: in this case, deactivate the VPS.
- The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this
case, contaminations caused by contact with other materials might occur. These contaminations will cause
marks and stains to develop. In these cases (e.g. when the helmet is kept in the top case on hot days), it is
recommended to make sure the VPS is not touching other materials.
7. VPS Disassembly
To remove the sun screen from the helmet, lift the helmet chin guard and lower the VPS by rotating the side slider
completely upwards (Fig.12B).
Hold the left lateral part of the sun screen and pull it toward the outside of the helmet (Fig.13).
Repeat the same operation on the right side of the helmet.
8. VPS Assembly
To assemble the sun screen on the helmet, lift the helmet chin guard and push the side slider completely upwards
(Fig.12B).
Insert the sun screen left end into the left side guide until the grip pawl is hooked in shell housing (Fig.13).
WARNING
- Use the special slider to activate/deactivate the VPS; do not deactivate the VPS by handling it directly.
- The VPS can only be used during the day and under the environmental conditions described before.
- At night and/or in conditions of poor visibility, the VPS must be deactivated.
- Always check that the VPS is properly positioned according to different weather/environmental conditions
and/or the above-mentioned recommendations for use.
- We recommend using the VPS only and solely together with the approved standard visor, which has a
transmittance value greater than 80%.
- The VPS does not replace the protection guaranteed by the visor.
- Always make sure that the VPS is clean and that it is operating properly in order to avoid scratches and/or
anomalous wear on it every time it is activated.
- As for VPS and visor maintenance and cleaning operations, please refer to the appropriate section in the
- The VPS scratch-resistant/fog-resistant treatment highly reduces fogging. Protracted periods of adverse
weather and/or environmental conditions might cause fogging and/or formation of condensation on the VPS,
which entails a reduction of visibility and/or sharpness of vision: in this case, deactivate the VPS.
- In case of rain, the direct contact of raindrops with the scratch-resistant/fog-resistant treated VPS quickly
reduces sharpness of vision, thus causing scarce visibility: in this case, deactivate the VPS.
- The special VPS fog-resistant treatment is usually sensitive to high temperatures or heat sources. In this
case, contaminations caused by contact with other materials might occur. These contaminations will cause
marks and stains to develop. In these cases (e.g. when the helmet is kept in the top case on hot days), it is
recommended to make sure the VPS is not touching other materials.
7. VPS Disassembly
To remove the sun screen from the helmet, lift the helmet chin guard and lower the VPS by rotating the side slider
completely upwards (Fig.12B).
Hold the left lateral part of the sun screen and pull it toward the outside of the helmet (Fig.13).
Repeat the same operation on the right side of the helmet.
8. VPS Assembly
To assemble the sun screen on the helmet, lift the helmet chin guard and push the side slider completely upwards
(Fig.12B).
Insert the sun screen left end into the left side guide until the grip pawl is hooked in shell housing (Fig.13).