X-LITE X-1004 Seguridad E Instrucciones página 9

Checking and Adjusting the PINLOCK® Inner Visor Stretch
Check the correct PINLOCK® inner visor assembly by opening and closing the visor and making sure that they do
not move. If the PINLOCK® inner visor is not tightly fixed to the visor, move both external adjustment levers
upwards to increase the stretch (Fig.10). This operation must be carried out gradually. The maximum stretch is
achieved when the pin adjustment external levers are turned outwards.
WARNING
- The presence of dust between the two visors may produce scratches on both surfaces.
- Scratched PINLOCK® visors and inner visors may cause reduced visibility and must therefore be replaced.
- Regularly check the correct stretch of the PINLOCK® inner visor to prevent it from moving and scratching
both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check that the PINLOCK® inner
visor is both correctly assembled and stretched.
- An excessive and early stretch of the PINLOCK® inner visor may result in excessive adherence against the
visor surface and/or permanent deformations with subsequent inability to correctly perform any following
adjustments.
- Intense sweating/breathing, the use under particular weather conditions (low temperatures, and/or high
humidity and/or sudden changes in temperature and/or heavy rain) and/or intense and prolonged use may
affect the performance of the PINLOCK® inner visor and cause fogging or formation of condensation. In such
cases, after using the helmet and to restore the system efficiency, remove the PINLOCK® inner visor from
the helmet visor and let it dry with dry and warm air. The same procedure must be applied to the helmet, in
order to dry out humidity in case it has formed up as a consequence of the conditions described above.
6. PINLOCK® Inner Visor Disassembly
6.1. Remove the visor equipped with the PINLOCK® inner visor (see instructions above).
6.2. Widen the visor and release the PINLOCK® inner visor from the pins (Fig.9).
6.3. Release the visor.
Maintenance and Cleaning
- Remove the PINLOCK® inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral
liquid soap. Remove the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.
Checking and Adjusting the PINLOCK® Inner Visor Stretch
Check the correct PINLOCK® inner visor assembly by opening and closing the visor and making sure that they do
not move. If the PINLOCK® inner visor is not tightly fixed to the visor, move both external adjustment levers
upwards to increase the stretch (Fig.10). This operation must be carried out gradually. The maximum stretch is
achieved when the pin adjustment external levers are turned outwards.
WARNING
- The presence of dust between the two visors may produce scratches on both surfaces.
- Scratched PINLOCK® visors and inner visors may cause reduced visibility and must therefore be replaced.
- Regularly check the correct stretch of the PINLOCK® inner visor to prevent it from moving and scratching
both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check that the PINLOCK® inner
visor is both correctly assembled and stretched.
- An excessive and early stretch of the PINLOCK® inner visor may result in excessive adherence against the
visor surface and/or permanent deformations with subsequent inability to correctly perform any following
adjustments.
- Intense sweating/breathing, the use under particular weather conditions (low temperatures, and/or high
humidity and/or sudden changes in temperature and/or heavy rain) and/or intense and prolonged use may
affect the performance of the PINLOCK® inner visor and cause fogging or formation of condensation. In such
cases, after using the helmet and to restore the system efficiency, remove the PINLOCK® inner visor from
the helmet visor and let it dry with dry and warm air. The same procedure must be applied to the helmet, in
order to dry out humidity in case it has formed up as a consequence of the conditions described above.
6. PINLOCK® Inner Visor Disassembly
6.1. Remove the visor equipped with the PINLOCK® inner visor (see instructions above).
6.2. Widen the visor and release the PINLOCK® inner visor from the pins (Fig.9).
6.3. Release the visor.
Maintenance and Cleaning
- Remove the PINLOCK® inner visor from the visor. Using a damp and soft cloth, gently clean it with neutral
liquid soap. Remove the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.