Troubleshooting - Aigostar 8433325503024 Instrucciones

GB
Uneven place may possibly cause the turnover switch at abnormal position, then the heater can't
work after turning on, therefore, please put the heater on the flat place, at least the surface below
the base of the heater must be flat.
Temperature Control Knob
Insert the plug into the power socket, then turn the Temperature Control knob clockwise, when
hearing the "poop" sound (it means the temperature controller is on), adjust the Temperature Control
knob to the desired temperature level.
Power Selection Knob
Turn the Power selection knob to select between 3 functions: Fan only,Low 1200W (LOW), High
2000W(HIGH).
Turn off the Heater
A. Turn the Power selection knob to OFF position.
B. Turn the Temperature Control knob anticlockwise to the initial position.
C. Remove the power plug, store the heater after the entire machine has become cool.
Safety Protection
1. Overheat protection: When the temperature in the heater is too high due to abnormality in the use
environment or improper use, the thermostat device can automatically cut off the power and the
heater stops working. After the whole heater is cooling, the heater can return to the normal use after
removing the abnormality.
2. Inversion protection: When the whole heater is inverted, the safety system will automatically cut off
the power, and return to the work state before inversion after the body is placed upright.
SAFETY CONTROL
Your heater is fitted with a safety device "Double Protector" that (1) switches off the heater by thermal
cut-off in the event of overheating or malfunction, It will reset while the temperature reduce to a
normal level. (2) Shuts off the heater by thermal fuse in the event of overheating or malfunction and
not operates by some other accidental reason.
If overheating or malfunctions continue, return the heater to an Approved Service Agent for
examination.
The most common cause of overheating is deposits of dust or fluff entering the heater, Ensure these
deposits are removed regularly by unplugging the unit and vacuum cleaning air vents and front
grille.
PILOT LIGHT
This fan heater is equipped with a pilot light that glows whenever the heater is plugged in and turned on.
It will continue to glow even if the thermostat has cycled the heating elements off. This feature is to
prevent you from being unaware that the heater is operating and maintaining the temperature of the
room.
When you do not wish the heater to control the room temperature, turn the control switch to O (off ) and
remove the plug from the electrical outlet.
GB-03
CLEANING AND MAINTENANCE
1. Light accumulated dust may be removed from the heater with a soft cloth. Wipe the exterior surfaces of
the heater occasionally with a cloth moistened (not dripping wet) with a solution of mild detergent and
water. Dry the case thoroughly with a soft dry cloth before operating the heater.
2. The fan motor is lubricated by the factory, and will require no further lubrication.
3. No other user maintenance is required or recommended. If service is required, send your heater to the
nearest authorized service depot.
4. Store heater in a clean and dry place when not in use.
REMEMBER - portable electric heaters are designed for spot heating, or as a supplementary heat source.
They are not intended to be main sources of heat during the normal heating season.
Note: There may be trace of smoke or odour when unit is first operated. Do not be alarmed. This
indicates that a drop of oil fell on the heating coil during the manufacturing process. It will quickly
evaporate, and should not re-occur.

Troubleshooting

If the product does not operate or does not operate properly, first check according to the following
list. If the reason the product does not operate or does not operate properly is not included in the
following list, the product mayhave failed. At this time, it is recommended to send the product to
the dealer or the Media Service Center for treatment.
Problem Possible Cause
The plug may not be plugged
After the power is engaged, the
well.
power indicator light does not
illuminate and the machine does
not work.
The temperature control knob is
not turned in place.
The temperature exceeds the
The machine suddenly stops
threshold of the thermal
during heating.
cut-oFF.
READ AND SAVE THESE INSTRUCTIONS
WARRANTY: 2YEARS
GB
Solution
Check whether the plug is
properly inserted into the
receptacle.
Check whether the
temperature control knob is
turned to the ON position.
Cool the machine before
use.
GB-04