HP LaserJet Pro MFP M148 Manual De Instrucciones página 6

Use the scan feature
Use the HP Scan software on your computer to start a scan job at the printer.
Windows
Click Start, select Programs or All Programs, select HP, and then
select HP Scan.
Troubleshooting
Wireless connection troubleshooting
NOTE: Both 2.4 GHz and 5 GHz bands are supported.
Verify that the printer is within the range of the wireless network. For most networks, the printer must be within 30 m (100 ft) of the wireless access
point (wireless router). A USB cable might be required for temporary connection between the printer and the computer. To ensure that the wireless setup
information synchronizes correctly, do not connect the USB cable until prompted to do so.
Follow these steps to restore the network settings:
1. Remove the USB cable from the printer.
2. Follow one of these steps:
a. For a 2-line control panel printer: Press and hold the Wireless
LED start blinking simultaneously, release the Wireless
b. For a touchscreen control panel printer: Go to the Setup menu on your printer, select Network Setup, and then select Restore Defaults/Restore
Network Settings.
The printer will restore network default automatically and restart.
3. When the Ready LED is on, continue to install the software.
If your router supports Wi-Fi Protected Setup (WPS) mode, try to connect
through this mode:
1. Press the WPS button on your router.
2. Within two minutes, press and hold the Wireless
three seconds and then release the button (2-line control panel printer),
or open the Setup menu, select Network Setup, select Wireless, select
Wi-Fi Protected Setup, and then tap the Push button from touchscreen
control panel.
3. The Wireless LED and the Ready
Wait while the printer establishes the network connection automatically.
4. This process takes up to two minutes. When the network connection is
established, the Wireless
to install the software.
Wireless printing
For more information about wireless
printing and wireless setup, go to
www.hp.com/go/wirelessprinting.
User guide and additional support resources
The user guide includes printer usage and troubleshooting information.
It is available on the web: Go to
or www.hp.com/support/ljM227MFP.
Check for firmware updates
1. Go to www.hp.com/support/ljM148MFP
or www.hp.com/support/ljM227MFP.
2. Select a printer or category from the list, and then click Drivers.
3. Select the operating system, and click the Next button.
4. Select Firmware, and click the Download button.
button for at least
LED start blinking simultaneously.
LED stops blinking and remains on. Continue
www.hp.com/support/ljM148MFP
Mac OS
Go to the Applications folder and open HP Easy Scan.
button on the printer control panel. When the Ready
button.
Check the Wireless LED status from the printer control panel:
1. If the Wireless
established.
a. Press the Wireless
Wireless on option from the Wireless menu on the control panel.
b. After the Wireless
the software. When the network connection is established,
the Wireless
2. If the Wireless
is established.
a. Check the network name (SSID) info on the Configuration
Report/ Network Summary: From the Reports menu, select
Network Summary. Verify the network name (SSID) on the report.
b. Make sure the computer is connected to the same wireless network
to which you are connecting the printer.
c. Continue to install the software.
3. If the Wireless
is not established.
a. Restart the printer and the router.
b. Manually connect the printer to your wireless network. Use Wi-Fi
Protected Setup (WPS) to connect the printer if the router supports
WPS, or continue to the next step.
c. Uninstall and reinstall the HP software.
Control panel help (touchscreen models only)
Touch the Help button on the printer control panel to access help topics.
6
LED and the Attention
LED is off, it means that the wireless connection is not
button on the printer control panel or select the
LED starts blinking, continue to install
LED stops blinking and remains on.
LED is on, it means that the wireless connection
LED is blinking, it means that the wireless connection