JUNO IC4RAL 07LM 30K 90CRI FL 120 FRPC Instrucciones De Instalación

JUNO 4" INTERNALLY ADJUSTABLE LED REMODEL
RECESSED HOUSINGS
WARNING: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn off electricity at the
fuse or circuit breaker box.
NOTE: Juno recessed fixtures are designed to meet the latest NEC requirements and are listed in full compliance with the relevant UL standard(s).
Before attempting installation of any recessed lighting fixture, check your local electrical building code. This code sets the wiring standards and installation
requirements for your locality and should be understood before starting work. Use of non-Juno trims voids Juno warranty.
SAVE THESE INSTRUCTIONS
TYPE TC FOR
NON-INSULATED CEILINGS
3"
Figure 1A
Juno Type TC fixtures are designed for installations
where the housing and J-Box will not come into contact
with insulation*. Insulation and combustible materials
must be spaced at least 3" away from the housing
and J-Box (Fig 1A).
*In Canada, when insulation is present, Type IC fixtures
must be used.
TYPE IC FOR
INSULATED CEILINGS
Figure 1B
Juno Type IC fixtures are designed for direct contact
with insulating materials that are approved for this
application (Fig. 1B). Fixtures may also be used in non-
insulated ceilings.
This Juno Air-Loc LED fixture is supplied with means to
seal the housing after installation for energy savings and
to comply with energy code air leakage requirements
per ASTM E283.
INSTALLATION STEPS
Note: This housing is compatible
with ceiling thicknesses from
1/2" to 1-1/2".
Step 1. Remove LED module
from carton and store in a safe
place for future installation.
Step 2. Locate center of
proposed opening on ceiling and
use template to mark and accurately
cut a 4-3/8" opening (Fig. 2).
Step 3. Follow steps 1-4 under Electrical Connection.
Step 3a. Remove paint shield and retain for use
as necessary.
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/juno-recessed
©2017 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
Step 4. Insert housing through ceiling opening and
press flush to ceiling (Fig. 3). Push retention clips
outward until they click into position. Note: To remove
housing from ceiling, push tab on clip upward to
disengage.
Step 5. Plug connector at the end of whip in the
housing into the LED module. Align the module with
the mating feature in the top plate and clip into place.
Be careful not to pinch wires between LED module
and housing. Fasten Philips head screws 2 places
to prevent module from unintentionally becoming
dislodged (Fig. 4).
Step 6. To seal housing after confirming correct
operation, apply supplied tape strips to completely
cover each of the three retention clips and slots.
Do not substitute with other materials (Fig. 5).
Retention
Clips
LED
Module
Figure 2
Plug
Connector
Rev 3/17
Figure 3
Align mating
details.
Screws
2x
Figure 4
P3832
Tape Strips to
Cover Springs
(3 Places)
Figure 5
FIXTURE DIMMING AND WIRING
120VAC (120) Driver
120VAC input housings. Dimmable with the use of most
incandescent, magnetic low voltage, or electronic low
voltage dimmers (Note: electronic low voltage dimmers
require a neutral wire connection at the dimmer.)
Universal Voltage (MVOLT) Driver
Universal input voltage (120VAC thru 277VAC)
housings. Dimmable with the use of most
SWITCHED HOT
BLACK
WHITE NEUTRAL
120VAC - 277VAC
GREEN GROUND
LED DRIVER
WITH OPTIONAL
0-10V DIMMING
VIOLET (+) POSITIVE
GREY (-) NEGATIVE
FIXTURE J-BOX
0-10V dimmers.
Lutron (ECOS3) Driver
Universal input voltage (120VAC thru 277VAC)
housings with Lutron ® Hi-Lume ® A-Series driver for use
with Lutron ® approved 3-wire fluorescent dimmers or
Ecosystem digital controls.
SWITCHED HOT
BLACK
DIMMED HOT
ORANGE
120VAC - 277VAC
WHITE NEUTRAL
LUTRON HI-LUME
GREEN GROUND
A-SERIES
LED DRIVER
VIOLET ECOSYSTEM BUS E1
GREY ECOSYSTEM BUS E2
FIXTURE J-BOX
** NOTE: CHOOSE EITHER 3-WIRE FLUORESCENT OR
ECOSYSTEM DIMMING (ONE OF THESE DIMMING OPTIONS
IS REQUIRED). LEAVE ORANGE WIRE OR VIOLET/GRAY
WIRES CAPPED ACCORDINGLY.
120V TO 277V
SUPPLY
CONNECTIONS
0-10V DIMMING
CONNECTIONS
(OPTIONAL)
120V TO 277V
3-WIRE
FLUORESCENT
DIMMER
CONNECTIONS**
ECOSYSTEM
DIGITAL
DIMMING**
1 of 2