Important Safety Instructions; Work Area; Electrical Safety; Personal Safety - DeWalt D25500 Manual De Instrucciones

Ocultar thumbs Ver también para D25500:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

582429-00/D25500 etc
1/29/03

Important Safety Instructions

WARNING: Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire
and /or serious persoinal injury.
SAVE THESE INSTRUCTIONS

WORK AREA

Keep your work area clean and well lit. Cluttered benches and
dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating
a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Grounded tools must be plugged into an outlet properly
installed and grounded in accordance with all codes and
ordinances. Never remove the grounding prong or modify the
plug in any way. Do not use any adapter plugs. Check with a
qualified electrician if you are in doubt as to whether the outlet is
properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry
electricity away from the user.
(Grounded) tools.
Double insulated tools are equipped with a polarized plug (one
blade is wider than the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way.
Double Insulation
eliminates the need for the three wire
grounded power cord and grounded power supply system.
Applicable only to Class ll tools.
Avoid body contact with grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of
9:29 AM
Page 1
Applicable only to Class I
electric shock if your body is grounded.
Don't expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock. Other
liquids, such as perspiration, present the same hazard.
Do not abuse the cord. Never use the cord to carry the tools or
pull the plug from an outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged cords immediately.
Damaged cords increase the risk of electric shock.
When operating a power tool outside, use an outdoor
extension cord marked "W-A" or "W." These cords are rated
for outdoor use and reduce the risk of electric shock. When using
an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating.
The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next
heavier gage. The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts
120V
0-25
26-50
240V
0-50
51-100
Ampere Rating
More
Not more
Than
Than
10 -
12
16
12 -
16
14

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools may result in
serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain
long hair. Keep your hair, clothing, and gloves away from moving
1
Total Length of Cord in Feet
51-100
101-150
101-200
201-300
AWG
16
14
12
12
Not Recommended

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

D25550D25600D25650D25551D25830D25850

Tabla de contenido