Axxess AX-ADXSVI-CH3 Instrucciones De Instalación

Dodge/RAM accessory and NAV output CAN harness 2013-up
• Provides accessory (12 volt 10 amp)
• Retains R.A.P. (retained accessory power)
• Used in non-amplified systems or when replacing amplified system
• Provides NAV outputs (parking brake, reverse, and V.S.S.)
• Prewired ASWC-1 harness included (ASWC-1 sold separately)
• Retains back-up camera (if through the OE radio)
• Retains the use of the 3.5mm AUX jack
• High level speaker input
• USB updatable
Note:
This harness must be used along with the AX-ADXSVI
DODGE
Dart
(small screen option) 2013-2016
WIRING THE AX-ADXSVI-CH3
• Connect the Yellow wire to the radio's 12 volt battery or memory wire.
• Connect the Black wire to the radio's ground wire.
• Connect the Red wire to the ignition wire of the aftermarket radio.
• Connect the Orange wire to the illumination wire of the aftermarket radio. If the
aftermarket radio has no illumination wire, tape off the Orange wire.
• Connect the White wire to the left front positive speaker output of the aftermarket radio.
• Connect the White/Black wire to the left front negative speaker output of the aftermarket radio.
• Tape off and disregard the following (1) wire, will not be used in this application:
Blue/White labeled "500L amp turn on"
Integrate • AxxessInterfaces.com
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
AX-ADXSVI-CH3
INSTALLATION INSTRUCTIONS
APPLICATIONS
RAM
1500, 2500, 3500
(small screen option)
Chassis cab 3500, 4500, 5500
(small screen option)
REV. 8/28/17
• Connect the Gray wire to the right front positive speaker output of the aftermarket radio.
• Connect the Gray/Black wire to the right front negative speaker output of the aftermarket radio.
• Connect the Green wire to the radio's left rear positive speaker output.
• Connect the Green/Black wire to the radio's left rear negative speaker output.
• Connect the Purple wire to the radio's right rear positive speaker output.
• Connect the Purple/Black wire to the radio's right rear negative speaker output.
The following wires are for the aftermarket radios that have navigation built in.
• Connect the Light Green wire to the parking brake wire of the aftermarket navigation radio (if applicable).
• Connect the Blue/Pink wire to the VSS or speed sense wire of the aftermarket navigation radio (if applicable).
• Connect the Green/Purple wire to the reverse wire of the aftermarket navigation radio (if applicable).
• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to test the radio.
• Tape off and disregard the following (1) wire, will not be used in this application:
Blue/White labeled "500L amp turn on".
2013-up
• Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE back up camera (if equipped).
• Connect the White and Red RCA to the audio "AUX in" of the aftermarket radio to retain the OE 3.5mm jack
2013-up
(if equipped).
After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the AX-ADXSVI-CH3 and refer to the
ASWC-1 instructions.
K
® NOWLEDGE IS
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
AX-ADXSVI-CH3
INSTALLATION INSTRUCTIONS
RCA CONNECTIONS
ASWC-1 (IF INSTALLING)
P
OWER
CAUTION! All accessories, switches, climate controls
panels, and especially air bag indicator lights must
be connected before cycling the ignition. Also, do
not remove the factory radio with the key in the on
position, or while the vehicle is running.
Integrate • AxxessInterfaces.com
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/28/17