Remote Control; Mounting And Connection - IMG STAGELINE CU-3IR Manual De Instrucciones

CU-3IR
Order No. 38.4060
Controller for 12 V or 24 V LEDs
GB
Please read these operating instructions carefully
prior to operation and keep them for later refer-
ence.
1 Applications
The controller CU-3IR is used to control LEDs or
LED chains requiring an operating voltage
between 12 V and 24 V . The maximum total
power consumption of all LEDs connected must
not exceed 10 A. From the product range of "img
Stage Line", for example, the following items can
be operated with the controller:
LEDL-9/RGB
LEDM-3/RGB
LEDS-5/RGB
LEDS-5MP/RGB
LEDS-5WP/RGB
2 Important Notes
The unit corresponds to all required directives of
the EU and is therefore marked with
The unit is suitable for indoor use only. Protect
G
it against dripping water and splash water, high
air humidity, and heat (admissible ambient tem-
perature range 0 – 40 °C).
For cleaning only use a dry, soft cloth; never
G
use chemicals or water.
No guarantee claims for the unit and no liability
G
for any resulting personal damage or material
damage will be accepted if the unit is used for
other purposes than originally intended, if it is
not correctly connected or operated, if it is over-
loaded or not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harmful
to the environment.

3 Mounting and Connection

1) Fasten the controller via screws at a suitable
place, if required. Make sure that the infrared
sensor IR (2) will always be visible when the
remote control is used.
2) Connect the LEDs to the terminals OUTPUT
(1). The total load by the LEDs must not
exceed 10 A; otherwise the controller will be
damaged.
R = negative pole for the red LEDs
G = negative pole for the green LEDs
B = negative pole for the blue LEDs
+ = common positive pole
POWER
CU-3IR
3-CH. LED CONTROLLER
IR IR
OUTPUT INPUT DATA
–
R G B + + A
1 2 3
Copyright
®
3) For power supply, a regulated power supply
unit will be required. Adjust the power supply
unit to the voltage required for the LEDs con-
nected (12 V
supply unit must be able to deliver the current
required for operating the LEDs plus a supply
current of 100 mA for the CU-3IR. Connect the
power supply unit to the contacts INPUT (3).
4 Operation

4.1 Remote control

When pressing a button, always direct the remote
control towards the sensor IR (2). There must be
no obstacles between the remote control and the
sensor.
If the range of the remote control decreases,
replace the battery. For this purpose, push the
lock on the rear side to the right while removing
the battery support downwards at the same time.
.
Insert the battery (lithium button cell of type CR
2032) into the support with the positive pole show-
ing upwards, then reinsert the support into the
remote control until it engages.
If the remote control is not used for a longer
period, remove the battery to prevent damage to
the remote control due to battery leakage.
Dead batteries must not be placed in the
household waste. To protect the envi-
ronment, always take them to a special
waste disposal, e. g. collection container
at your retailer.
4.2 Selecting a control programme
Select the desired programme with the buttons
MODE (6):
0 The programmes 1 – 16 will be executed auto-
matically one after the other.
1 Change of colour: red – green – yellow – blue
– purple – cyan – white
2 Change of colour: red – green – blue
3 Flashing in red
4 Flashing in green
5 Flashing in blue
6 Gradual change: red – blue – green
7 The LEDs will show blue,
continuously becoming brighter and darker.
8 The LEDs will show green,
continuously becoming brighter and darker.
6
M/S WORK
7
B
8
9
4 5
by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved.
©
min., 24 V max.). The power
1.
2.
1
MODE
2
10
3
SPEED
4
5
BRT
6
PAUSE
9 The LEDs will show red,
continuously becoming brighter and darker.
10 The LEDs will show cyan,
continuously becoming brighter and darker.
11 The LEDs will show yellow,
continuously becoming brighter and darker.
12 The LEDs will show purple,
continuously becoming brighter and darker.
13 The LEDs will show white,
continuously becoming brighter and darker.
14 Gradual change: red – blue
15 Gradual change: blue – green
16 Gradual change: green – red
Six programmes can be directly selected with the
buttons 1 – 6 (10):
Button Progr. No. Programme
change of colour: red – green – yellow –
1
1
blue – purple – cyan – white
2 2 change of colour: red – green – blue
3
6 gradual change: red – blue – green
4 14 gradual change: red – blue
5 15 gradual change: blue – green
6 16 gradual change: green – red
4.3 Brightness, speed, pause
1) Adjust the brightness of the LEDs connected
with the button BRT (8). Nine brightness levels
are available.
2) Adjust the execution speed of the control pro-
gramme selected with the buttons SPEED (7).
Nine speed levels are available.
3) With the button PAUSE (9), the control pro-
gramme can be paused and continued again.
If, for example, the LEDs are to light continu-
ously in a certain colour, press the button
PAUSE when the desired colour is shown dur-
ing the gradual change.
5 Specifications
Power rating: . . . . . . . . . . . 10 A max.
Power supply: . . . . . . . . . . 12 – 24 V ,
depending on the LEDs con-
nected
No-load current: . . . . . . . . approx. 100 mA
Ambient temperature: . . . . 0 – 40 °C
Dimensions: . . . . . . . . . . . 115 × 55 × 20 mm
Weight: . . . . . . . . . . . . . . . 185 g
Subject to technical modification.
1 Terminals OUTPUT for the LEDs
2 IR receiver for the remote control signals
3 Terminals INPUT for the operating voltage
The operating voltage must correspond to the voltage
required for the LEDs connected
12 V min., 24 V max.
4 Terminals DATA for an extension module
5 LEDs
POWER power indication
M / S will light continuously
WORK will light to the rhythm of the control programme
6 Buttons MODE to select a control programme
7 Buttons SPEED for the speed (9 levels)
8 Button BRT for the brightness (9 levels)
9 Button PAUSE to pause / continue the programme execution
10 Button for direct selection of six programmes
A-1013.99.01.07.2009