Horizon Global 24974 Instrucciones De Instalación página 3

Always wear SAFETY GLASSES
when installing hitch
r
Figure 2
4.5"
4.5"
6.5"
Figure 3
2.5"
4"
Figure 4
Note: Be sure to leave all hardware loose until installation is complete
1. Remove Fascia
1. Remove (12) push rivets located on the lower side of the fascia
2. Using a screw driver, remove (4) screws located in each wheel well
3. Remove taillight by removing the (1) screw located inside the hatch opening, underneath the screw cover. Carefully pull the taillight rearward
4. Remove (2) screws under the hatch, near trunk opening
5. Remove fascia. If equipped: detach the rear sensor plugs from the fascia before removing fascia
2. Lower exhaust – using a 12mm socket, remove (2) nuts that secure the exhaust hangers on each side of the vehicle. Using exhaust removal pliers, lower the muffler by removing the (2) forward exhaust
hangers in front of the rear axel. Note: be sure to secure the exhaust before lowering.
3. Remove the heat shields using a 10mm socket remove (6) screws from each heat shield. Set aside for later reinstallation. Using a screwdriver, remove the center fascia support on the bumper. If
interference occurs, use pliers to bend the metal fascia support out of the way.
4. Install support brackets – remove the foam tape from the side of the frame and the plug from the access holes on the bottom of the vehicle frame. If needed, remove the caulking from the frame. Insert
the coiled end of the pullwire into the mounting hole and out the access hole. Insert the wire through the block (item 5) and attach the 7/16 bolt (item 1), see figure 2. Pull the wire and align the bolt with
the mounting hole. Raise the support bracket into position and attach the bracket using (3) M10x1.25x40mm bolts (item 3) and (3) conical tooth washers (item 2). Repeat the process for the bracket on
the other side of the vehicle.
5. Raise hitch into position – attach using item 6, 7, and 8.
6. Torque all 7/16-14 Gr5 fasteners to 50 Lb.-Ft. (68 N*m), all 1/2-13 Gr5 fasteners to 75 Lb.-Ft. (102 N*m), and all 10mm CL10.9 fasteners to 42 Lb.-Ft. (57 N*m).
7. Trim heat shield according to figure 3
8. Trim fascia according to figure 4 and replace fascia by reversing step 1 including the heatshields, exhaust, and taillights.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced.
Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York,
V.E.S.C. Regulation V-5 and SAE J684.
©2017 Horizon Global Americas Inc. - Printed in Mexico
Installation Instructions
PART NUMBERS: 24974, 77974, CQT24974
Frame
weldnut
6.5"
Authorized Drawbar Kit:
3593 (Sold Separately)
Drawbar must be used in the RISE
position only.
Pull wire access location
j
n
p
o
q
Figure 1
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 3 of 18
Fastener Kit: 24974F
① Qty.(2)
Bolt 7/16-14x1.50
Gr. 5
② Qty. (8) Conical Tooth
Washer 7/16"
Part no. 01292007
l Qty. (6) M10 x 1.25 x 40mm
CL 10.9
m Qty. (2) 7/16-14 Hex Nut
n Qty. (2) Block 1/4 x 7/8 x 3.0
Part no. HE-2370-000
o Qty. (4) Conical Tooth
m
Washer 1/2
Part no. 01292008
p Qty. (4) Bolt 1/2-13x1.75
Gr. 5
k
q Qty. (4) 1/2-13 Hex Nut
r Qty, (2) Pull wire 7/16
Part no. 5481
Conical Washer
l
Fasteners
Teeth side
typical
Against hitch
both sides
24974NP 03-26-18 Rev. A