Dyna-Glo RA125DGD Instrucciones De Funcionamiento Y Manual De Piezas página 3

Dyna-Glo Delux Operating Instructions and Parts Manual
Model R 125DGD
General Safety Information
(Continued)
10. Use this heater only as described in
this manual. ny other use not
recommended by the manufacturer
may cause a fire or injury to persons.
11. Provide adequate ventilation. Before
using heater, provide at least a 3.0
square foot opening of fresh, outside
air for every 100,000 BTU/Hr rating.
12. Do not modify or alter this heater in
any way or operate any heater that has
been modified from its original state.
13. It is hard to anticipate every use
which may be made of the heater.
Check with your local fire safety
authority if you have any questions
about heater application.
14. Be sure heater is on a solid and level
surface.
Propane Gas: Propane gas is odorless. n
odor-making agent is added to propane
gas. The odor helps you detect a propane
gas leak. However, this odor may fade in
time. Propane gas may be present in the
area even though no odor is detected.
15. Use only propane gas. Do not
attempt to use natural gas.
16. Keep appliance clear and free from
combustible materials, gasoline,
paint thinner, and other flammable
vapors and liquids. Dust is com-
bustible. Do not use heaters in areas
with high dust content.
17. Check heater for damage before each
use. Do not use damaged heater.
Minimum heater clearance from
combustibles:
Sides: 6 feet Top: 5 feet
Floor: Combustible - Not for use
on finished floors
For Technical Support or Troubleshooting, Call: 1-877-477-4768, 8:00 am - 5:00 pm CST
18. The heater, other than a heater
with an integral propane gas
cylinder, must be located at
least (i) 6 ft. (1.83 m) in the U.S.;
or (ii) 10 ft. (3 m) in Canada,
from any propane gas cylinder.
19. The propane cylinder supply system
must be arranged to provide for
vapor withdrawal from the
operating cylinder.
20. Blower or radiant type heaters shall
not be directed toward any propane
gas cylinder within 20 feet (6 m).
21. Check hose before each use of
heater. Do not use if hose is cut or
damaged. Replace with hose
specified by manufacturer.
22. The heater is not intended for use
on finished floors. Warping or other
damage may occur.
23. Place heater away from any breezes
or drafts. Keep away from dripping
water or rain.
24. Keep small children and animals
away from the heater.
25. lways wear gloves when handling
the heater to prevent injury.
26. Never attach ductwork to heater.
27. Use only original replacement parts.
This heater must use design specific
parts. Do not substitute or use generic
parts. Improper replacement parts
could cause serious or fatal injury.
ssembly
1. Provide propane gas supply only.
2. Connect heater to a proper gas supply
using the supplied regulator, and turn
knob on LP cylinder on.
3
3. Wait 5 minutes for any gas to clear.
Smell for gas; if you do not smell gas,
heater is ready to operate.
Never use an open
flame to check for a
leak. pply 50/50 mixture of liquid soap
and water to all joints. Bubbles forming
show a leak. Correct all leaks at once.
Operation
This heater should only be used with
a tank that has a vapor withdrawal
system. Refer to the Standard of
Storage and Handling of Liquefied
Petroleum Gas, NSI/NFP 58, Chapter
5. Your local fire department or library
will have this information.
TO ST RT HE TER
1. Follow all of the safety, ventilation
and installation instructions
previously noted in this manual.
2. lways be sure to place the heater on a
stable and level surface while the heater
is in operation. Be sure that no strong
winds blow into the ends of the heater.
Figure 2 – Control Knob
3. Turn control knob clockwise to OFF
position.
4. Turn LP gas supply valve on.
5. Depress heater control knob and turn
counterclockwise to (IGN) LOW
position to light burner.
www.ghpgroupinc.com
PROFESSIONAL GRADE
E
N
G
L
I
S
H