Using The Appliance - Philips 1000 Serie Manual De Instrucciones

English
introduction
Congratulations on your purchase and welcome
to Philips! To fully benefit from the support that
Philips offers, register your product at www.philips.
com/welcome.
Your new Philips Professional Power hair clipper
enables comfortable clipping of even the toughest
hair. To enjoy using the hair clipper, we advise you
to read the following information.
general description (Fig. 1)
A Cutting element
B Clipping attachment
C On/off slide
D Handle
E Socket for appliance plug
F Large comb
g Small comb
h Setting indications
i Stubble comb
J
Setting selector
K Appliance plug
l Adapter
M Cleaning brush
important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- Check if the voltage indicated on the adapter
and on the appliance corresponds to the
local mains voltage before you connect the
appliance.
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug,
as this causes a hazardous situation.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
- Children should be supervised to ensure that
they do not play with the appliance.
- Remove the clipping attachment from
the handle before you clean the clipping
attachment under the tap.
Caution
- Never immerse the handle in water or any
other liquid, nor rinse it under the tap.
- Do not use the appliance in the bath or in the
shower.
- The clipping attachment of the appliance
complies with the internationally approved IEC
safety regulations and can be safely cleaned
under a tap (Fig. 2).
- Use and store the appliance at a temperature
between 15°C and 35°C.
- Only use the adapter supplied.
- If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
- Do not use the appliance when the clipping
attachment or one of the combs is damaged or
broken as this may cause injury.
- This appliance is only intended for clipping
human scalp hair. Do not use it for any other
purpose.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
4222.002.8009.1
user manual, the appliance is safe to use based on
scientific evidence available today.

Using the appliance

Preparing for hair clipping
Only use the appliance on clean, dry hair. Do not
use it on freshly washed hair.
1 Make sure that the head of the person whose
hair you intend to cut is at the same level as
your chest. This ensures that all parts of the
head are clearly visible and within easy reach.
2 Comb the hair in the growth direction (Fig. 3).
Clipping with comb
The appliance comes with three combs for 15
different hair lengths.
The minimum remaining hair length is 1.6mm and
the maximum remaining hair length is 41mm.
1 Select the comb you want to use.
The table shows how long the hair will be after
clipping at the different settings of the small comb
and large comb.
settings of the small and large comb and
large
Setting Hair length
after clipping
with small
comb
1 3mm
2 6mm
3 9mm
4 12mm
5 15mm
6 18mm
7 21mm
Tip: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
stubble comb for a 'stubble look'
- To create a 'stubble look', clip with the small
comb set to setting 1 (3mm) first.
- Then clip the hair with the stubble comb for a
hair length of 1.6mm.
2 Slide the selected comb into the guiding
grooves on both sides of the handle
('click') (Fig. 4).
3 To set the comb to the desired setting, press
the setting selector (1) and slide the comb to
the desired hair length setting (2) (Fig. 5).
The setting indications on the comb show the
,
selected setting.
4 Put the adapter into the wall socket.
5 Switch on the appliance.
6 Move the appliance through the hair slowly.
- To clip in the most effective way, move the
appliance against the direction of hair growth.
- Since all hair does not grow in the same
direction, you need to move the appliance in
different directions (upward, downward or
across) (Fig. 6).
- Make sure that the flat part of the comb is
always fully in contact with the scalp to obtain
an even result.
- Make overlapping passes over the head to
ensure that you cut all the hair that needs to
be cut.
- To achieve a good result with curly, sparse or
long hair, use a hand comb to guide the hair
towards the appliance.
7 Regularly remove cut hair from the comb.
If a lot of hair has accumulated in the comb,
remove the comb from the appliance and blow
and/or shake the hair out of it.
Contouring without comb
You can use the appliance without comb to clip
hair very close to the skin (0.6mm) or to contour
the neckline and the area around the ears.
Be careful when you clip without comb because
the cutting element removes every hair it
touches.
1 Pull the comb off the appliance (Fig. 7).
2 Before you start to contour the hairline
around the ears, comb the hair ends over the
ears.
3 Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends when you shape the contours around
the ears (Fig. 8).
Only cut the hair ends. The hairline should be close
to the ear.
4 To contour the neckline and sideburns,
Hair length
turn the appliance and make downward
after clipping
strokes (Fig. 9).
with large
Move the appliance slowly and smoothly. Follow
comb
the natural hairline.
23mm
Cleaning
26mm
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as
29mm
petrol or acetone or ethereal oils to clean the
32mm
appliance.
35mm
Note: The appliance does not need any lubrication.
38mm
Clean the appliance every time you have used it.
41mm
1 Make sure the appliance is switched off and
disconnected from the mains.
2 Remove the comb from the appliance.
3 To remove the clipping attachment, turn
it anticlockwise until the open dot on the
handle is aligned with the arrow on the
attachment (1). Then lift the attachment off
the handle (2) (Fig. 10).
4 Push the centre top end of the cutting
element upwards with your thumb
until it opens and then pull it off the
appliance (Fig. 11).
Be careful that the cutting element does not fall on
the floor.
5 Clean the cutting element with warm water
(max. 40°C).
6 Clean the clipping attachment under warm
running water to flush out the cut hair that
has accumulated in the attachment (Fig. 12).
7 After cleaning, place the lug of the cutting
element in the slot of the clipping attachment
and push the cutting element back onto the
clipping attachment (Fig. 13).
8 Clean the handle and the adapter with the
cleaning brush supplied or a dry cloth.
Note: The handle and the adapter are not water-
proof.
9 Let the cutting element and the clipping
attachment dry completely before you
reassemble the appliance.
2/9