5_Initial Configuration; Connecting Snap To The Remote Control; Snap App Configuration And Connection To Cloud; Download The App - ELICA SNAP Manual De Instrucciones

5_Initial configuration

Snap, after being first connected to power supply, carries out visible setup operations through luminous feedback of the central led light and
the luminous ring. When this is completed, Snap prepares itself for the following configuration phases.
5.1

CONNECTING SNAP TO THE REMOTE CONTROL

5.1.1
EN
SET SNAP ONTO THE REMOTE CONTROL RECEPTION PHASE
From the first moment it is switched on, Snap automatically
searches for the signal for 5 minutes.
When Snap is ready to be connected, its luminous ring turns orange.
If 5 minutes have passed and you still have not interacted with Snap, or you have decided to postpone the remote control connection to another time, it is
possible to activate the signal reception phase in two different ways:
a
by quickly pressing down through the reset section of the App, which is reachable
(1 sec) the reset key, located by carryingout the following procedure (Home/Single
under the Snap glass Snap Menu/Settings/Snap Reset/Hood and Remote
Control Connection/Start Remote Control Reset)
When Snap is ready to be connected, its luminous ring turns orange.
WARNING! In case of previously connected remote controls, both ways (a and b) will delete any previous connection.
5.1.2
COMPLETING THE SNAP-REMOTE CONTROL CONNECTION
In order to complete the remote control connection, press the following
key combination: DIMMER + RGB for a prolonged period of time (>1sec).
Successful connection is confirmed when the luminous ring turns
green and Snap gives off two acoustic signals.
After a few seconds, Snap goes into stand- by mode, the luminous
ring switches off and the central led turns white.
WARNING!
If no command is activated, Snap goes back into stand -by mode
or to the previously set feature. In order to connect the remote
control, Snap must be brought back into reception phase through
Snap itself or by using the App.
5.1.3
CONNECTING SNAP TO MORE THAN ONE REMOTE CONTROL
If you wish to add new remote controls, use the already connected
one and press the following key combination: ON/OFF + DIMMER
for a prolonged period of time (>1sec) to set Snap onto the new
remote control connection phase.
The luminous ring becomes orange, where you can see as many
single green led lights as the number of remote controls already
connected to Snap.
To complete the remote control configuration step, please follow
14
the instructions given in point 5.1.2
remote control reception
a and b
remote control reception
b
Successful remote control connection
stand-by
successful connection of other
remote controls
5.2

SNAP APP CONFIGURATION AND CONNECTION TO CLOUD

Before starting the configuration procedure, we recommend that you:
a_Obtain the SSDI name and Wi-Fi password, if you wish to connect Snap in this way.
b_You must have an active email, where a confirmation code that is used for login, will be sent to.
Therefore, carry out the following steps:
central
logo is off
5.2.1
+
luminous

DOWNLOAD THE APP

ring is orange
Install the APP (SNAP, AIR QUALITY BALANCER) on your
Smartphone or Tablet. Search for 'Snap App' on PLAY STORE for
Android and on the APP STORE for iOS.
5.2.2
CREATE AN ACCOUNT
After opening the APP, follow the guided steps to register and
create your own account.
You must enter Name, Surname, Email Address and Password
(which must be at least 8 characters and contain at least one
capital letter, one lowercase letter and a minimum of one number.
central E.g.: Rossi2015). At the end of registration, an email will be sent to
logo is off
the given email address, containing a confirmation code that must
+
be entered into the App. In the case that the email is not found in
luminous
your in box, check your Spam.
ring is orange
It is also possible to register through your Facebook profile.
After concluding the registration phase, decide how you prefer to
use your Snap:
a_Wi-Fi Model: single configuration possible
> connection through Wi-Fi
b_Wi-Fi + SIM Model: two possible configurations, choose between
central
> Wi-Fi connection
logo is off
+ > SIM DATA connection
luminous
WARNING! Never close the App from now on.
ring is green
5.2.3
SET SNAP ONTO DIRECT CONNECTION FROM SMARTPHONE
OR TABLET RECEPTION PHASE
It is possible to activate direct connection in two different ways:
central
logo is white a_By pressing the reset key located under the Snap glass for a
+
prolonged period of time (>5sec – until you hear an acoustic signal
luminous
and the see the luminous feedback, described hereunder).
ring is off
b_Through remote
key combination: ON/OFF + RGB for a prolonged period of time
(>1sec).
Successful setup of direct connection of Snap is confirmed
when a luminous orange dot begins to rotate clockwise on
the ring.
central logo is off
+
WARNING!
luminous
Once the reception phase is activated, Snap waits for its next
ring is orange
command for 20 minutes. Any key which is pressed on the remote
+
control during this phase, inhibits the stand -by mode and brings
single green
leds are on Snap back onto the previously set feature.
control: by pressing the following
by pressing the reset key
located under the Snap
EN
a b
through remote control
waiting for direct connection
from Smartphone or Tablet
central
logo is off
+
orange dot
on the luminous
ring
15