6_Snap-Hood Connection - ELICA SNAP Manual De Instrucciones

5.2.4
COMPLETING SNAP DIRECT CONNECTION FROM SMARTPHONE
OR TABLET
In order to carry out direct connection, go back to your Smart-
phone or Tablet, activate the Wi-Fi connection and connect to the
network: SNAP_XXXX.
The luminous red dot turns green and two acoustic signals confirm
EN successful connection.
5.2.5
CONNECTING TO CLOUD
Snap is now ready to connect to cloud.
Follow procedure 5.2.5.A if you have chosen connection via Wi-Fi.
Follow procedure 5.2.5.B if you have chosen connection via SIM DATA.
5.2.5.A
CONNECTION VIA WI-FI
Go back to the App and follow the guided procedure to configure
your Snap and enter:
_Your SSID name and network Password
_The name you want to give your Snap
_The requested information needed to optimize Snap operation.
To complete the connection of Snap to CLOUD, select "send" on the App.
Follow the final instructions in the App and wait 90 seconds.
The luminous dot remains green, and a luminous trail appears on the bottom, whose colour changes
from orange to green to confirm successful connection.
To confirm the procedure carried out has been successful, the luminous ring turns green and Snap
gets off two acoustic signals.
WARNING!
If there is no connection, the problems with connection to cloud
luminous ring turns red and
central logo
Snap gives off an acoustic
is off
signal.
+
Follow the APP instructions
luminous ring
to repeat the procedure.
is red
16
successful direct connection
from Smartphone or Tablet
central
logo is off
+
green dot
on the luminous
ring
5.2.5.B
CONNECTION VIA SIM DATA
Go back to the App and follow the guided procedure to
configure your Snap and enter:
_The name you want to give your Snap
_The requested information needed to optimize Snap
operation.
waiting for the connection signal
central logo is off
+
green dot on the
luminous ring
+
orange and then
green trail on the
bottom
connection procedure ok
central logo
is off
+
luminous ring
is green
6_Snap–hood connection
Thanks to the integrated Link function, the suitable Elica Sense hoods
can activate Snap when smoke and odour levels go above filtering
capacity.
Before carrying out the connection, make sure that the hood is on
Stand- by mode, and not on the aspiration phase.
6.1
SET SNAP ONTO HOOD RECEPTION PHASE
It is possible to set Snap onto signal reception phase in three different
ways:
a_By pressing the reset key twice, which is found under the Snap glass.
b_Through the App, in the Snap reset section, which is reachable by following
(HOME > SINGLE SNAP MENU > SETTINGS > SNAP RESET > REMOTE
CONTROL AND HOOD CONNECTION > START HOOD RESET)
c_By remote control: by pressing the following key combination:
ON/OFF + DRY for a prolonged period of time (>1sec).
Successful set-up of Snap into the reception phase is confirmed when
the luminous ring turns orange and rotates in a 'double flow 'way.
WARNING! This waiting phase lasts 3 minutes.
Any key that is pressed on the remote control, during this phase, inhibits
the reception mode.
6.2
COMPLETING THE SNAP- HOOD CONNECTION
In order to conclude the connection phase, simply set the hood into
Sensor mode (for further information see your Elica hood instruction
booklet) and Snap is automatically connected.
Successful connection is confirmed when the luminous ring turns green
and rotates in a 'double flow' and Snap gives off two acoustic signals.
After a few seconds, Snap automatically goes into Link mode.
The central led turns orange.
WARNING!
If no commands are activated, Snap goes back to the previous mode/
feature. To 'disconnect' the hood, set Snap into connection phase and
do not activate any command.
a
EN
by pressing the reset key
located under the Snap
b
through the App
c
by remote control
hood reception
central
logo is off
+
luminous ring
is orange
successful hood connection
central
logo is off
+
luminous
ring is green
link function
central
logo is orange
17