Energy Saving; Auto Shut-Off - Bosch B25L Instrucciones De Uso

• If the appliance does not have variable steam control,
press the steam release button only for a few seconds
at a time when ironing at lower temperatures.
In both cases, if you find that water is dripping out of the
soleplate, set the temperature selector (13) to a higher
position (take care that the garment can be ironed on this
heat temperature setting).
2. At the beginning of each use, it is possible that drops
of water will be dispensed alongside steam. Therefore,
it is advisable to try the iron on the ironing board or a
piece of cloth to start with.
Ironing without steam
1. Begin ironing but without pressing the steam release
button (15).
Vertical steam (C)
1. Set the temperature control to the "•••" or "max"
position.
2. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a vertical
position and pressing the steam release button (15).
Never direct the steam jet at garments that are being
worn.
Never aim the steam at people or animals.

Energy saving

If the "Energy saving" button (4) is switched on, you
can save up to 25% of the energy and 40% of the water
consumption, and still have a good ironing result for most
of your garments. It is advisable to use the normal energy
setting only for thick and highly wrinkled fabrics.
Intelligent steam
(depending on model)
This system has intelligent steam control, which, after
releasing the steam release button (15), provides a small
amount of additional steam.
The additional steam can always be stopped by briefly
pressing the steam release button once again.

Auto shut-off

(depending on the model)
If during ironing the steam release button (15) on the
handle of the iron is not pressed for a certain length of
time (8 minutes), the steam station will automatically
switch off.
The "Auto shut-off" pilot lamp (7) will flash when auto
shut-off has been activated.
To switch the steam station back on, press the steam
release button again, and wait until the "Auto shut-off"
pilot lamp remains lit continuously.
Cleaning & Maintenance
Always unplug the appliance from the mains supply
before carrying out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and allow the appliance
to cool down before cleaning.
2. Wipe the housing, handle and iron body with a damp
cloth.
3. If the soleplate is soiled with dirt or scale, clean it with
a damp cloth.
4. Never use abrasive products or solvents.
Storing the appliance (D)
1. Always allow the appliance to cool down before storing
it.
2. Set the main power to the "0" position and disconnect
the mains cable.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Empty the water tank and store the mains cable on the
cord rewind facility. Tidy the steam hose on the handle
of the iron using the cord clip provided (12). Do not
wrap the cords too tight.
Fabric protection soleplate cover (E)
(depending on the model)
The fabric-protection soleplate cover is used for steam-
ironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover also
does away with the need for a cloth to prevent shine on
dark materials.
It is advisable to first iron a small section on the inside of
the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until it
fits tightly. To release the soleplate cover, pull the elastic
strap and remove the iron.
The fabric-protection soleplate cover may be purchased
from the customer service or specialist shops:
Accessory code
(After-sales)
464846
464745*
* Cork handle iron
"Calc'n clean" (F)
Cleaning the Boiler
To extend the life of your steam generator and to avoid
any build up of scale, it is essential that you rinse out the
boiler after several hours of use (approximately after 50
hours). If the water is hard, increase the frequency.
en
Name of accessory
(Specialist outlets)
TDZ2510
TDZ2520*
13