Fabric Protection Soleplate Cover; Descaling The Filter And The Boiler; Energy Saving "Eco" Button - Bosch Sensixx B45L Instrucciones De Uso

D
Vertical steam
This can be used to remove creases from
hanging clothes, curtains etc.
It cannot be used on a synthetic setting for
delicate items.
Warning!:
• Never direct the steam jet at garments that are
being worn.
• Never aim the steam at people or animals.
1. Set the temperature to the
2. Hold the iron in an upright position setting 15 cm
away from the garment being steamed.
3. You can steam iron curtains and hanging
garments (jackets, suits, coats...) by placing the
iron in a vertical position and pressing the steam
release button (13 or 14*).
"Intelligent steam"
function
(Model dependent)
This system has intelligent steam control, which,
after releasing the steam release button, provides a
small amount of additional steam.
The additional steam can always be stopped by
briefly pressing the steam release button once again.
Energy saving
"eco" button
(Model dependent)
If the "Energy saving" button (7) is switched on, you
can save up to 25% of the energy and 40% of the
water consumption (*), and still achieve good results
when ironing most of your garments.
It is advisable to use the normal energy setting only
for thick and very wrinkled fabrics.
(*) In comparison to the maximum setting.
Note:
If you work with the "Energy saving" function,
the variable steam regulation and temperature
regulation can still be used as recommended.
"secure" auto shut-off
(Model dependent)
If during ironing, the steam release button (13-14*)
on the iron handle is not pressed for a certain length
of time (8 minutes), the steam station will
automatically switch off.
The " " icon will flash when auto shut-off has
been activated (three beeps may be heard).
20
B O SC H
To switch the steam station back on, press the steam
release button again.
E
(Model dependent)
The fabric-protection soleplate cover is used for
steam ironing delicate garments at maximum
temperature without damaging them. Use of the
soleplate cover also does away with the need for a
cloth to prevent shine on dark materials.
setting.
It is advisable to first iron a small section on the
inside of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and
pull the elastic strap over the lower rear of the iron
until it fits tightly. To release the soleplate cover, pull
the elastic strap and remove the iron.
The fabric-protection soleplate cover may be purcha sed
from the customer service or specialist shops :
(Calc'n'Clean Advanced)
To extend the life of your steam generator and to
avoid any build up of scale, it is essential that you
rinse out the filter (12*) and the boiler after several
hours of use (approximately after 50 hours). If the
water is hard, increase the frequency.
Do not use descaling agents for rinsing out the
boiler, as they could damage it.
If the "
boiler must be rinsed (three beeps may be heard).
Please proceed as follows:
1. Check carefully that the appliance is cold and
2. Fix the iron to the stand by inserting the tip of
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the
5. Unscrew the filter (12*) and take it out.
6. To wash the scale collector, place it under the water tap
Fabric protection
soleplate cover
Accessory code
(After-sales)
00571510
Descaling the filter
F
and the boiler
" icon flashes, this indicates that the
unplugged for more than 2 hours, and that the
water tank (1) is empty.
the iron into the front slot and moving the fixation
lever (10) against the heel of the iron.
filter opening.
and wash it up until calc residues are removed. Squeeze
it as indicated in the picture a).
To obtain the best result, you may immerse the scale
collector for approximately 30 minutes in tap water (250
ml) mixed with a measure (25 ml) of descaling fluid, as
Name of accessory
(Specialist outlets)
TDZ2045