Tork SA400 Guía De Instrucciones

PROGRAMMING INSTRUCTIONS
This product has passed
ETL testing. It is certified
SA400
and complies with both
U.S. and Canadian
product safety standards.
MODE Button
Calendar/7-5-2 Button
REVERSE Button
RESET Button
Time Set Button
ON/OFF/Enter Button
RANDOM Button
MODE Button
PROGRAM Button
Calendar/7-5-2 Button
REVERSE Button
ZIP-SET
RESET Button
DST Button
Zip-Set/Clear Button
BUTTON DIAGRAM
BATTERY INSTALLATION
Neutral
Neutral
Line Line (Hot)
120 or 277 VAC
Ground
Input Only
Load
BATTERY INSTALLATION
MOUNTING HOLES
120 or 277 VAC
Input Only
ONE YEAR LIMITED WARRANTY: If this product fails because of a
manufacturing defect within one year after purchase, we will, at our option,
either repair or replace it at no charge. Our warranty does not cover damage
caused by accident, abuse or misuse. We assume no further liability with respect
to the sale or use of this product. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTY OF
MERCHANTABILITY. We make no warranty with respect to the fitness of any
goods for the users particular application. This warranty gives you specific legal
rights, and you also may have other rights which vary from state to state.
It is our intent to provide accurate and current specification information.
However, in the interest of product improvement, TORK may alter the
specifications or constructional details without prior notice.
FOR TECHNICAL SUPPORT: techsupport@nsiindustries.com 877.230.7874
Calendar/7-5-2 Button
REVERSE Button
MODE Button
RESET Button
CONTACT RATINGS:
• 120/277VAC 60 Hz.
Calendar/7-5-2 Button
BUTTON DIAGRAM
• 40 AMP Resistive
• 40 AMP Inductive
REVERSE Button
• 30 AMP Tungsten
• 30 AMP Incandescent
ZIP-SET
• 120VAC 1 1/2 HP Motor RESET Button
INSTALLATION AND MOUNTING
Time Set Button
Mount the timer in the desired location using the three mounting holes
ON/OFF/Enter Button
(A, B, C) provided. The best mounting position for the timer is at eye
BUTTON DIAGRAM
level with sufficient room for the door cover to swing fully open. The top
mounting hole (A) is a slotted type mounting hole, so measure and secure
this to the wall with the first (A) screw. The head of the screw (or fastener)
should be slightly larger than the narrow portion of the slotted hole. Hang
RANDOM Button
the timer on screw A. Screw timer into the wall using the remaining two
mounting holes (B and C) to provide a secure permanent mounting for
the timer.
PROGRAM Button
NOTE: Mount case in a vertical position using mounting holes provided.
BATTERY INSTALLATION
EASY WIRING
1. Turn power OFF at circuit breaker or fuse.
ZIP-SET
2. Strip 5/8 inch of the wire insulation.
3. Unscrew, lift and twist plastic protective cover to access the terminals.
DST Button
4. Identify your Line and Load wires.
5. Run your wires through the knockouts and cable clamp wire connectors (not provided).
Zip-Set/Clear Button
6. Connect and tighten the ground wire to grounding terminal at bottom of case.
BUTTON DIAGRAM
7. Insert the wire ends under the proper terminal plates and tighten the screws firmly.
8. Check Voltage. Unit is factory preset for 120V operation. For 277V operation, remove screw from
voltage switch cover above terminals. Slide switch to the right for 277V position. Replace cover.
9. Replace the plastic protective cover.
10. Restore power at fuse box or circuit breaker. Turn power ON.
TIMER OPERATION
MANUAL OVERRIDE
To override the ON or OFF settings, press the ON/OFF button. The override setting will not change
the next timed event. TURN OFF ALL TIMER FUNCTIONS. If you do not want to use any timer
functions, press the MODE button until "OFF" is displayed.
MOUNTING HOLES
UNDERSTANDING THE ZIP-SET MODE
FRENCH
ZIP-SET mode is use to set the TIME and set an outdoor lighting program in one easy step. When
completed, the SA400 will have the proper time and be set to turn ON at Sunset and OFF after 6
hours. The OFF time can be adjusted in the mode also.
ZIP-SET is pre-set to the 212 area code (New York City) time zone so no adjustment is needed for this
area code. If you live in New York within the 212 area code, simply press the MODE button to "ZIP"
and you are done.
NEUTRE
Ligne Charge
NOTE: Do not touch the time setting! It must always be set to the Default Preset Factory Time (NYC -
(212) local time) for the ZIP-SET program to work.
Neutre
SET TIME WITH ZIP-SET MODE
Simply enter your telephone area code by following these easy steps Ligne
Chargé
to have the time adjust to your location:
Masse
120/277 V c.a.
1. (Figure A) Press the MODE Button until "ZIP" appears in the
entrée
uniquement
display.
2. Press and hold the ZIP-SET/Clear button until the display shows
MOUNTING HOLES
the 3-digit area code input mode (Figure B).
Charge
3. The 1st digit of the telephone area code should be flashing.
Press the FORWARD/HOURLY Adjust or REVERSE Button to
120/277 V c.a.
entrée
adjust it, then press ON/OFF/ENTER button to enter it and edit
uniquement
the next digit. Press the ZIP SET/Clear button to go back to edit
the previous digit. Continue until the correct telephone area code is
displayed.
4. (Figure C) Once your telephone area code is entered select a turn
OFF time for the ZIP-SET automatic sunset timer (the default turn
OFF time of 6 should flash). You can have the timer turn OFF 2, 4, 6,
8, 10, 12, 14, or 16 hours after sunset - or a fixed time, 12:30am,
1:00am, 1:30am, etc. While the turn OFF time is flashing press the
FORWARD/HOURLY Adjust to cycle to the desired turn OFF
setting, then press ON/OFF/ENTER button to enter it. (Figure D)
When "DONE" appears in the display, press ON/OFF/ENTER button to confirm or wait 10 seconds.
5. Press MODE button to Zip (display icon) to confirm the timer is set for ZIP-SET Auto ON at Sunset.
NSi Industries LLC • USA • www.nsiindustries.com
ZIP-SET
RANDOM Button
NOTE: DST Button
1. After entering the Area codes for certain states, a "C" may appear next to the telephone area Zip-Set/Clear Button
PROGRAM Button
code, indicating a central location in the state. Press FORWARD or REVERSE to toggle to W
(West) or E (East) and N (North) or S (South) if needed for proper time setting.
2. There are also area codes that may have different time zones; for example the 208 area code; by
default will flash PST or by pressing FORWARD or REVERSE will toggle to MST.
3. Telephone area codes can change and may not appear in the timer's table. Should that occur,
please use the closest adjacent area code to set the timer correctly for your location.
DST Button 4. If a new area code was issued after this unit was manufactured or if you enter an invalid/
nonexistent area code, you will get an error message stating, "AREA CODE NOT FOUND". Enter the
Zip-Set/Clear Button
closest correct area code for ZIP-SET mode to function properly.
5. If the clock/calendar is not correct or time is lost after replacing batteries, ZIP-SET mode will not
function properly. Please see SETTING CLOCK AND CALENDAR (below).
ACTIVATE THE ZIP-SET SUNSET TIMER
1. Press the MODE button until "ZIP" icon is displayed. The ZIP-SET sunset timer is set and active.
2. SA400, once properly set, knows the sunset time of your location. It will automatically turn on
at sunset and turn OFF after your selected duration time of 2, 4, 6, 8, 10, 12, 14 or 16 hours (see
ZIP-SET Telephone Area Code Setting)- or at a fixed time, 12:30am, 1:00am, 1:30am, etc.
MOUNTING HOLES
3. Press the RANDOM button once to activate the random feature so the timer ON/OFF time will
fluctuate between +/-10 minutes to +/-120 minutes randomly. To cancel this feature, just press the
button again (random disappears). When your home is left unattended, this is an excellent security
feature to simulate household activity and random should be activated.
USING PROGRAMMABLE ON AND OFF TIME SETTINGS
The SA400 has 2 independent programmable ON/OFF time
settings so you can turn outdoor holiday, landscape and
security lighting, etc. ON and OFF at specific times. The third
setting (12) runs the combination of program 1 and program
2 times for the days selected.
1. Press MODE Button until the "PROG" and "1" icons are
displayed.
2. Press the CALENDAR/7-5-2 button to select the timer
frequency. "7" means the timer will operate all week, "5" for
weekdays and "2" for just the weekend.
3. (Figure E) Press and hold the PROGRAM button until the
display is flashing.
4. The display will change to show the "ON" time for
program 1 and flash. The "ON" icon will appear. Press the
FORWARD/HOURLY ADJUST or REVERSE button to
adjust the ON time.
SPANISH
5. (Figure F) Press the ON/OFF/ENTER button or wait for approx. 10 seconds. The display will
show OFF time, and the "OFF" icon will appear. Press the FORWARD/HOURLY ADJUST or
REVERSE button to adjust OFF time. Press the ON/OFF/ENTER button once more or wait for
approx. 10 seconds to return to normal mode. Display will change back to show the clock time.
6. To program 2nd, 3rd or 4th timer, just follow step 1-5 but press MODE button until "PROG" and
corresponding ("2" or "12") icons are displayed.
NEUTRO
Carga
Línea
NOTE: Do not program the same ON and OFF time when setting programs 1, 2, or 12. You cannot
set the turn on and turn OFF to the same time (i.e., Turn on at 5:00 am and turn OFF at 5:00 am).
Doing so will produce an error message on the display. To resolve the error message, change the OFF
FRENCH
Neutro
time by at least one minute using the FORWARD or REVERSE button.
Línea Calor
ACTIVATING THE PROGRAMMABLE TIMER
120/277 VCA Suelo
1. Press MODE button until one of the program icons appears. That programmed timer is now
SOLO ENTRADA
active. (Press the PROGRAM button to view the existing ON and OFF preset times).
2. There is a simpler way to adjust turn on time by pressing the FORWARD/HOURLY ADJUST
button. The turn ON can be adjusted by +/-90 minutes.
Carga
3. If you wish, press the RANDOM button once to activate the random feature. The timer ON/OFF
time will fluctuate +/-10 to +/-120 minutes randomly. To cancel this feature, just press the button 120/277 VCA
SOLO ENTRADA
again.
ACTIVATE THE PROGRAMMABLE TIMER
1. Press MODE button until the wanted program icon (PROG 1, 2 or 12) is displayed and the chosen
timer program will be active.
2. Press the RANDOM button once to activate the random feature so the timer ON/OFF period
will fluctuate between +/-10 minutes to +/-120 minutes randomly. To cancel this feature, press the
button again (random disappears). Turn OFF all timer functions. If you don't want to use any timer
functions, just press the MODE button until "OFF" is displayed. Confirm timer settings for ON/OFF:
Press MODE, select program then press PROGRAM button.
(Voyant allumé)
BATTERY REPLACEMENT
This unit comes with 2 x CR2032 batteries for time keeping and backup. You should replace the
batteries every 2 years. To replace the batteries, please follow these steps:
1. Turn power OFF at circuit breaker to remove fuse.
2. Use a small Philips screwdriver to remove screw holding the battery compartment.
FRENCH
3. Use a small flat screwdriver gently pry the battery door open. Remove the 2 x old CR2032
batteries.
4. Install 2 x new CR2032 batteries into the battery compartment, making sure that the + and –
polarities match up with the diagram printed on the unit.
5. When the batteries are in place, return the battery door its original position and tighten the
screws.
6. If you find the timer is not running after installing new batteries, you may need to reset it first.
Using the point of a pencil or paperclip, press the RESET button located on the front panel. You will
then need to reset the time and date.
NOTE: When changing batteries, make sure to reset the current time to the correct time in the
Eastern time zone. When you enter your telephone area code, it will then automatically adjust to the
proper time for your location/time zone. If Reset: ZIP-SET must have the area code, year and date
and Eastern time entered properly to function.
SETTING CLOCK AND CALENDAR
Clock Setting (this function is usually used when batteries must be replaced). Set only to Eastern
Time- 212 area code.
1. Press and hold the TIME SET button until the display is flashing.
2. Press and hold the FORWARD/HOURLY ADJUST button to rapidly advance the time forward,
or the REVERSE Button to rapidly change the time backward. Release button when the approximate
correct Eastern time is displayed. PM Indicator is on the upper right corner of the display.
NOTE: While pressing either FORWARD/HOURLY ADJUST or REVERSE button the minutes
will begin at a moderate pace, and then get faster. This will help you in set the time faster and more
accurately.
3. Press the FORWARD/HOURLY ADJUST or REVERSE button repeatedly until the correct
Eastern time is displayed.
4. Press the ON/OFF/ENTER button or wait for approx. 10 seconds to exit time setting mode.
5. The Daylight Savings Time Indicator is to the right of the display. Press the DST button to ON to
(Voyant allumé)
have timer increase the current time by 1 hour for daylight saving time. Press the DST button again
to turn it OFF. Current time will decrease 1 hour.
CALENDAR SETTING (This function is usually used when batteries must be replaced)
1. Press and hold the CALENDAR/7-5-2 button until "Y 04" (default) flashes on the display.
2. Press the FORWARD/HOURLY ADJUST or the REVERSE button to adjust to current year then
(Voyant éteint)
press ON/OFF/ENTER button or wait for approx. 10 seconds. The display will show month/date
and flash.
3. Press the FORWARD/HOURLY ADJUST or REVERSE button repeatedly until the correct
month/date is displayed.
4. Press the ON/OFF/ENTER button or wait for approx. 10 seconds to exit calendar setting mode.
NOTE: While pressing either FORWARD/HOURLY ADJUST or REVERSE button the date will
begin at a moderate pace, and then get faster. This will assist you in setting the time quickly and
accurately.
SPANISH
(Figura A)
(Figura B)
(Figura C)
(Figura D)
(Figura E)
(Luz encendida)
LI-972(A)