Tork D1060MW Instrucciones

LI-834(D)
©2023 NSI Industries
TRK_D1060MW_DTM_PrgmInstr
IN-WALL COUNTDOWN TIMER
D1060MW, D212HW
MODEL#:
INPUT RATINGS:
120VAC, 60Hz
OUTPUT RATINGS:
General Purpose 15A
Electronic Ballast 500VA
Resistive 15A
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND TEST THAT
POWER IS OFF BEFORE WIRING.
WARNING: TO AVOID OVERHEATING, USE ONLY 14AWG, 600V, 105˚C WIRE TO CONNECT THIS TIMER
INSTALLATION INSTRUCTIONS & WIRING DIAGRAM
UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN
1. Remove existing wall plate and switch , if applicable.
2. Connect wires per WIRING DIAGRAM as shown.
3. Mount timer into box with mounting screws and attach wall
plate into position.
4. Restore power at circuit breaker. Installation is complete.
OPERATING INSTRUCTIONS
TIME SETTING
To set timer, press the push button repeatedly to select one of the four time settings.
- FOR D1060MW: 10min - 20min - 30min - 60min
- FOR D212H: 2hr - 4hr - 8hr - 12hr
The illuminated LED indicates which time setting is selected.
Timer starts counting down until time out is reached and OFF LED is illuminated.
MANUAL OFF
To turn timer OFF manually, press the push button repeatedly until OFF LED is illuminated.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
ONE YEAR LIMITED WARRANTY: If this product fails because of a manufacturing defect within one year after purchase, we will, at our option, either repair or replace it at no charge. Our
warranty does not cover damage caused by accident, abuse or misuse. We assume no further liability with respect to the sale or use of this product. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTY OF MERCHANTABILITY. We make no warranty with respect to the fitness of any goods for the users particular application.
This warranty gives you specific legal rights, and you also may have other rights which vary from state to state.
It is our intent to provide accurate and current specification information. However, in the interest of product improvement, TORK may alter the specifications or constructional details without prior notice.
FOR TECHNICAL SUPPORT | SOUTIEN TECHNIQUE | PARA COMUNICARSE CON EL SERVICIO TÉCNICO
Tungsten 1000W
Ballast 1000VA
Motor 1/4HP
WIRING DIAGRAM
BLACK
GREEN
RED
WHITE
TM-008
NEUTRAL
(WHITE)
888.500.4598
LISTED
HOT
(BLACK)
GROUND
(GREEN)
LOAD
nsiindustries.com/tork
800.321.5847