Worx WX700 Manual De Instrucciones página 10

tool out of your control.
13. Do not run the power tool while
carrying it at your side. Accidental
contact with the spinning accessory could
snag your clothing, pulling the accessory
into your body.
14. Regularly clean the power tool's air
vents. The motor's fan will draw the
dust inside the housing and excessive
accumulation of powdered metal may
cause electrical hazards.
15. Do not operate the power tool near
flammable materials. Sparks could
ignite these materials.
16. Do not use accessories that require
liquid coolants. Using water or other
liquid coolants may result in electrocution
or shock.
17. your hand must hold on the handle
when you are working. Always use the
auxiliary handles supplied with the tool.
Loss of control can cause personal injury
FURTHER SAFETy INSTRUcTIONS FOR
ALL OPERATIONS
KIcKbAcK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
10
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of
the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged
or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can
dig into the surface of the material causing
the wheel to climb out or kick out. The wheel
may either jump toward or away from the
operator, depending on direction of the
wheel's movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below.
1. Maintain a firm grip on the power
tool and position your body and
arm to allow you to resist kickback
forces. Always use auxiliary handle, if
provided, for maximum control over
kickback or torque reaction during
start-up. The operator can control torque
Angle grinder
All manuals and user guides at all-guides.com
2. Never place your hand near the
3. Do not position your body in the
4. Use special care when working
5. Do not attach a saw chain
ADDITIONAL SAFETy INSTRUcTIONS
FOR GRINDING AND cUTTING-OFF
OPERATIONS
SAFETy WARNINGS SPEcIFIc FOR
GRINDING AND AbRASIVE cUTTING-
OFF OPERATIONS:
1. Use only wheel types that are
2. The guard must be securely attached
3. Wheels must be used only for
4. Always use undamaged wheel
reactions or kickback forces, if proper
precautions are taken.
rotating accessory. Accessory may
kickback over your hand.
area where power tool will move
if kickback occurs. Kickback will
propel the tool in direction opposite to
the wheel's movement at the point of
snagging.
corners, sharp edges etc. Avoid
bouncing and snagging the
accessory. Corners, sharp edges or
bouncing have a tendency to snag the
rotating accessory and cause loss of
control or kickback.
woodcarving blade or toothed saw
blade. Such blades create frequent
kickback and loss of control.
recommended for your power tool
and the specific guard designed for
the selected wheel. Wheels for which
the power tool was not designed cannot
be adequately guarded and are unsafe.
to the power tool and positioned
for maximum safety, so the least
amount of wheel is exposed towards
the operator. The guard helps to protect
operator from broken wheel fragments
and accidental contact with wheel.
recommended applications. For
example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side
forces applied to these wheels may cause
them to shatter.
flanges that are of correct size and
shape for your selected wheel. Proper
wheel flanges support the wheel thus
reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different
EN