Filter Care; Battery State Indicator - Bosch Unlimited BCS1 Serie Instrucciones De Uso

12
Fig.
Remove any dirt that may have been lodged under-
neath the container ejector opening.
Insert the filter unit into the dust container, making
sure it is correctly seated.
Insert the dust container into the appliance, so that
it clicks audibly into place.
!
Caution: If you notice any resistance when inserting
the dust container, check that the filter is complete
and that the filter unit and dust container are correct-
ly seated.

Filter care

The filters should be cleaned at regular intervals in or-
der to ensure that the vacuum cleaner operates opti-
mally.
Please switch off the appliance to clean the filters.
!
Caution: The filter can only be cleaned if the appli-
ance is switched off.
Remove the dust container from the appliance.
10
Fig.
Take the filter unit out of the dust container.
11
.
Fig
13
Fig. Cleaning the plate filter
To clean the plate filter, turn the knob at least three
turns through 180°.
Then remove the plate filter from the outer filter unit
and empty the dirt.
We recommend that you clean the plate filter each time
you empty the dust container.
14
Fig. Tapping the dirt out of the plate filter
If the plate filter is particularly dirty, the dirt can also
be tapped out.
To do this, remove the plate filter from the outer fil-
ter unit and tap it out over a dustbin.
Once you have cleaned the plate filter, it is ready for
use immediately.
!
Please note: The filter does not need to be rinsed
out.
15
Fig. Cleaning the fluff filter
Take the filter unit out of the dust container.
12
Fig.
a) It is usually sufficient to lightly shake or tap out the fluff
filter when the dust container is emptied in order to
dislodge any particles of dirt.
b) If this is not sufficient, you can use a dry cloth to remo-
ve dirt particles from the surface.
16
Fig.
Insert the plate filter into the outer filter unit and
lock it in place by turning it clockwise.
Insert the filter unit into the dust container, making
sure it is correctly seated. Insert the dust container
into the appliance, so that it clicks audibly into
12
place.
Fig.
46
Cleaning the floor nozzle
Before carrying out any maintenance, switch off the
vacuum cleaner and disconnect it from the charging
cable.
17
Fig.
a) Turn the rotary brush anti-clockwise
and pull it out to the side of the floor nozzle.
b) Use scissors to cut through threads and hairs wound
round the brush and then remove them.
c) Slide the rotary brush in at the side of the floor nozzle
and along the guide bar, and turn it clockwise
it in place.
!
Please note: The floor nozzle must only be used with
the rotary brush fitted.
Troubleshooting
Problem
Product doesn´t work
and no signal from batte-
ry status indicator
Continuos red battery
status indicator for 10
sec.
Care
Make sure that the cordeless handheld vacuum clea-
ner is switched off and disconnected from the charging
cable before cleaning it. The vacuum cleaner and plas-
tic accessories can be cleaned with standard plastic
cleaner.
!
Caution: Do not use abrasive, glass-cleaning or
all-purpose cleaning products. Never immerse the
vacuum cleaner in water.
Subject to technical modifications.

Battery state indicator

Operating status
Normal mode
Turbo mode
Battery capacity redu-
ced by 20%
Battery flat
Over-/undertemperature
protection
* Depending on model
to unlock it
r r
to lock
Possible solution
Please ensure that bat-
tery is assembled in cor-
rect way and/or battery
is charged.
Battery might be over/
under heated. Ple-
ase wait until battery
reaches suitable tempe-
ratures.
LED indicator
Green LED lit
Green LED flashing
quickly
Red LED flashing slowly
LED off
Red LED remains
continuously for 10 se-
conds, then goes out
lit