Morphy Richards PRECISE STEAM PLUS Instrucciones De Uso página 4

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12
E
The shot of steam can be used
whilst dry ironing, providing there is
water in the tank, and the
temperature control is set within the
steam range.
Do not use shot of steam at
temperatures below the steam
range (1-DOT) shown on the control
dial.
Note: For optimum steam quality,
F
do not operate the shot more than
three times in succession.
Vertical steam
Hold the iron in a vertical position
between 1cm and 2cm away from
the item E. Press the shot of steam
button fi, this will create vertical
steam. This feature is especially
useful for removing creases from
hanging clothes, curtains, wall
hanging, etc.
G
Note; For optimum steam quality,
do not operate the shot more than
three times in succession.
No drip system
Your iron is fitted with a no drip
system which is designed to
prevent water escaping from the
soleplate when the iron is too cold.
During use, the no drip system may
emit a loud click, particularly during
heat-up or whilst cooling down. This
is perfectly normal and indicates
that the system is functioning
correctly.
Auto shut-off
(certain models only)
If your iron is fitted with the auto
shut-off function it will automatically
shut down after a set period.
If the iron is left unattended in the
horizontal position it will shut down
after 1 minute. When this occurs,
the indicator light will flash and a
beep will be heard.
If it is left in the vertical position it
will shut down after 8 minutes.
6
To reactivate the iron gently shake
it, the temperature indicator light will
come on indicating the iron is
warming up and wait for the iron to
heat-up as normal.
LIFE LONG ANTI- SCALE
SYSTEM
(certain models only)
The life long anti-scale system
reduces scale deposits and helps
prolong the life of the iron.
EMPTYING AND
STORING
When you have finished ironing,
unplug your iron. Ensure that the
steam to dry iron selector switch ⁄
is set at the
position, lift up the
fill cap and empty any remaining
water out of the filling hole F.
Do not store in the box, but in an
upright position, so that any drops
of water remaining cannot leak out
and discolour the soleplate G.
Important: The flex can be damaged
if wound too tightly around the iron
after use. Make a loose loop with
the flex and wrap it around the iron.
The iron must be cool before
winding the flex and storing on its
heel.
MAINTENANCE
Self clean feature
1
Half fill the iron with water.
2
Place the iron on its heel.
3
Connect to a mains supply outlet
4
Turn the temperature dial to 'MAX'
setting
5
The pilot light will glow indicating
the irons switched on.
6
The pilot light will go off when the
required temperature is reached.
7
Wait for one more cycle;
(pilot light glows and goes off.)
8
Turn the temperature dial in anti-
clockwise direction to 'Min'
9
Disconnect the iron from mains
supply outlet.
To clean the exterior
10 Hold the iron horizontally over
a sink.
Allow the iron to cool and wipe over
with a damp cloth and mild
11 Press and hold down the Self-
detergent, then wipe with a dry
Cleaning button.
cloth.
12 Steam and boiling hot water will
YOUR TWO YEAR
drain from the holes in the the
soleplate washing away the scale
and minerals that have built up
inside the Steam Chamber.
13 Gently move the iron back and forth
proof of purchase. Staple your
until the water tank is empty.
receipt to this back cover for future
reference.
14 When Self-Cleaning is complete,
release the Self-Cleaning button.
Please quote the following
information if the product develops
15 Rest your steam iron back on its
a fault. These numbers can be
heel and allow to fully cool down.
found on the base of the product.
16 Wipe the soleplate with a cold
Model no.
damp cloth.
All Morphy Richards products are
WARNING: Keep hands and
individually tested before leaving the
body away from the hot water.
factory. In the unlikely event of any
appliance proving to be faulty within
WARNING: Do not attempt to
28 days of purchase it should be
descale the soleplate with
returned to the place of purchase
descaling products.
for it to be replaced.
If the fault develops after 28 days
To clean a stainless
and within 24 months of original
purchase, you should contact the
steel soleplate
Helpline number quoting Model
To keep the soleplate of your iron
number and Serial number on the
clean and free of limescale, we
product, or write to Morphy
recommend that you use one of the
Richards at the address shown. You
gentle chrome, silver or stainless
may be asked to return a copy of
steel cleaners that are generally
proof of purchase.
available. Always follow the
manufacturers instructions. To clean
Subject to the exclusions set out
off melted man-made fibres set the
below (see Exclusions) the faulty
iron at 3 dot position and pass it
appliance will then be repaired or
over a clean piece of cotton which
replaced and dispatched usually
will draw the deposit off the surface.
within 7 working days of receipt.
If for any reason this item is
To clean a coated
replaced during the 2 year
guarantee period, the guarantee on
soleplate
(certain models only)
the new item will be calculated from
In the unlikely event of any man-
original purchase date. Therefore it
made fibre fusing to the soleplate,
is vital to retain your original till
set the iron at the 3 dot position and
receipt or invoice to indicate the
pass it over a clean piece of cotton
date of initial purchase.
which will draw the deposit off the
surface.
To qualify for the 2 year guarantee
the appliance must have been used
Do not use scouring powder or
according to the manufacturers
solution as this could cause
instructions. For example kettles
damage to the coating.
should have been regularly
descaled.
GUARANTEE
It is important to retain
the retailers receipt as
Serial no.
g
7

Publicidad

Tabla de contenido
loading

Tabla de contenido