GE 21052 Guia De Inicio Rapido

MODEL NO. 21052
FOR INDOOR AND OUTDOOR USE
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
a)
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.
When products are used in outdoor applications, connect the product to a Ground Fault
Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar
sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or
nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric
shock it should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
o)
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well maintained and fresh.
Do not place on live trees in which the needles are brown or break off easily. Keep the
tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut,
damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures,
loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including
tree, branches, or bushes, to avoid any undue strain or stress on the product conductors,
connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
Replace the lamp.
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of lampholder.
3. Replace lamp with only 3.3 Volt, 0.066 Watt,
LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the lampholder.
CAUTION:
1. Replace lamps only with 3.3 volt, 0.066 watt spare lamps provided with this product.
2. Risk of fire. This product does not contain lamp shunts, which allow the product to operate
if one lamp burns out. Do not replace lamps with other than the spare lamps provided with
this product.
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com
©2018 Nicolas Holiday Inc., 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
If the product One or more of the based LEDs
does not light may have loosened from the
socket during transporting. There
is a break in the circuit between
the LED leads and the socket
terminals. Male/female
connectors not fully inserted
together. Non working control
box. Foot pedal in off position.
If a based LED One or more of the based bulbs
is missing may have come out of the socket
when transporting.
If an LED fails Incorrect LED, premature LED
to light (shorts failure or voltage is too high.
or opens)
LEDs fail to If applicable, then a defective
switch from control box or color change foot
white to multi pedal.
SH-18 PRINTED IN CHINA
CORRECTIVE ACTION
Unplug the set at the outlet. Starting with
the first unlit LED, gently push (don't twist)
each LED base firmly into the socket. If
still does not light, then remove each
based LED and check for out of place
lead wires. Make certain connectors fully
inserted and securing cap fully tightened.
Step on foot pedal to turn LEDs on.
Mark socket(s) with a piece of tape and
unplug the set. Replace the based LED or
use one of the spare based LEDs
included with product.
The LED may be out or dimly lit.
Replace bad LEDs as soon as you find
them.
Contact Customer Support.