Descargar Imprimir esta página
GE 21L JEWEL STAR Instrucciones De Servicio Para El Usuario
GE 21L JEWEL STAR Instrucciones De Servicio Para El Usuario

GE 21L JEWEL STAR Instrucciones De Servicio Para El Usuario

Publicidad

Enlaces rápidos

21L JEWEL STAR
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
a)
b)Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c)This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heater, fireplaces, candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let the lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock, it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use .
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.
l) Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
m) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
n) Do not cover the product with cloth, paper, or any material not part of the product when in use.
o)This product is equipped with push-in type lamps. Do not twist lamps.
p)This product employs overload protection (fuse). A blown fuse indicates an overload or short -circuit
situation. If the fuse blows, unplug the product. Replace the fuse as per the user servicing
instructions(follow product marking for proper fuse rating) and check the product.
If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
q) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on
live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including trees, branches,
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
-SEE OTHER SIDE-
MODEL NO.:
USER SERVICING INSTRUCTIONS
71026(0.14)
Fuse replacement:
A) Before changing fuses, make sure the set is unplugged.
b) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
c) Using a flathead screwdriver, open fuse cover.
Slide open the fuse access cover on top of attachment plug towards blades.
d) Remove fuses carefully .
e) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
f) Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.
Make sure door is fully closed and fuses are completely covered.
g) Risk of fire. Do not replace attachment plug. Contains a safety device(fuse) that should not be removed. Discard product if
the attachment plug is damaged.
Bulb replacement: Before changing bulbs, make sure set is unplugged.
Step 1: Grasp plug and remove from
the receptacle or other outlet device.
Do not unplug by pulling cord.
Step 2:Hold bulb by the plastic base
and pull bulb/base straight out of
socket.
If the spare bulbs provided with the product have no plastic base or the plastic
base does not fit, first follow steps 1-2 above. Then:
a) Remove the old bulb by straightening the bulb wires and pulling bulbs
straight from the base..
b) Replace the new bulb by straightening the bulb leads and aiming each
wire into a separate hole in the plastic base.
c) Make sure each bulb lead comes out an exit opening at the bottom of the plastic base. Now bend each lead up such that
each bulb lead fits closely against the narrow side of the plastic base.
CAUTION:
2. To reduce the risk of overheating, replace burned out lamps promptly. Use 6 Volt ,0.84 Watt lamps only.
3. To reduce the risk of fire and electric shock: a)Do not install on trees having needles, leaves or branch coverings of metal
or materials that look like metal, and b)Do not mount or support strings in a manner that can cut or damage wire insulation.
For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com.
FOR INDOOR USE ONLY
PRINTED IN CHINA
©2021 Nicolas Holiday Limited, 9F., No. 37, Guangfu N. Rd Taipei, Taiwan 10560. All rights reserved.
-CONTINUED FROM OTHER SIDE-
Most often, fuses blow because too many sets have been strung end-to-end.
Step 3:Replace lamp with only 6 Volt, 0.84 Watt
super brightness midget push-in type lamp
provided with product.
Push spare bulb/base assembly into socket. Do
not twist bulb when inserting into socket. If bulbs
are twisted, part of the set will not light.
1. This lighting string is rated 16.8 Watts ( 0.14 Amps), do not overload.
120 VOLTS
a
c
b
E246482 HC-21
MADE IN CHINA

Publicidad

loading

Resumen de contenidos para GE 21L JEWEL STAR

  • Página 1 -CONTINUED FROM OTHER SIDE- MODEL NO.: 21L JEWEL STAR USER SERVICING INSTRUCTIONS 71026(0.14) IMPORTANT SAFETY INSTRUCTIONS Fuse replacement: Most often, fuses blow because too many sets have been strung end-to-end. When using electric products, basic precautions should always be followed including the following: A) Before changing fuses, make sure the set is unplugged.
  • Página 2 -CONTINUACION- MODELO NO. : INSTRUCCIONES DE SERVICIO PARA EL USUARIO ESTRELLA CON JOYAS DE 21 LUCES 71026(0,14) INSTRUCCIONES IMPORTANTES DE SEGURIDAD Reemplazo de fusibles: Can frecuencia, los fusible se queman porque se han conectado Demasiados juegos de punta a punta. a) Antes de cambiar los fusible,asegúrese de desenchufar el juego.

Este manual también es adecuado para:

73026