SKI 2312 Instrucciones página 9

USE
• Charging battery 5
- battery of new tools is not fully charged
- after approximately 1 hour the battery is fully charged
! remove battery from charger after charging
period has ended thereby lengthening the service
life of the battery
IMPORTANT:
- while charging, the charger and the battery may
become warm to touch; this is normal and does not
indicate a problem
- ensure that the outside surface of the battery is clean
and dry before inserting into charger
- do not charge at temperatures below 0°C and over
40°C; this will seriously damage the battery as well
as the charger
- do not remove battery from tool while it is running
! a battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles
- do not repeatedly recharge the battery after only a
few minutes of operation; this may result in a
reduction of operating time and battery effi ciency
- the battery must be kept separate from the natural
environment and should not be disposed of as
normal domestic waste (symbol 6 will remind you of
this when the need for disposing occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
- if you anticipate long periods of non-use for the tool,
it is best to unplug the charger from its power source
• On/off 7
• Speed control for smooth starting 8
• Changing direction of rotation 9
- when not properly set in left/right position,
switch A 2 cannot be activated
! change direction of rotation only when tool is at a
complete standstill
• Changing bits 0
- push bit to end position in bitholder J
! do not use bits with a damaged shank
• Torque control (VariTorque) !
- limits the amount of output torque delivered by the
chuck (16 clutch settings)
- when turning in a screw, fi rst try VariTorque position 1
and increase until the desired depth has been
reached
• 2 Mechanical speeds @
- set switch E to desired speed
! change speed while tool is running slowly
1 = HIGH POWER
- high torque
- for screwdriving and drilling large diameters
- for tapping thread
2 = HIGH SPEED
- lower torque
- for drilling small diameters
• Screwbit identifi cation and storage #
• Identifi es and stores the right bit for a fl awless
screwdriving job
• Holding and guiding the tool $
- keep ventilation slots L 2 uncovered
- do not apply too much pressure on the tool; let the
tool do the work for you
APPLICATION ADVICE
• Use the appropriate bits %
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood ^
• Dustfree drilling in walls &
• Dustfree drilling in ceilings *
• Drilling in tiles without skidding (
• For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
• Keep tool and charger clean
- the charger may be cleaned most effectively with
compressed air (wear safety goggles)
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
• This SKIL product is guaranteed in accordance with
statutory/country-specifi c regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
• In case of a complaint, send the tool or charger
undismantled together with proof of purchase to your
dealer or the nearest SKIL service station (addresses as
well as the service diagram of the tool are listed on
www.skileurope.com)
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ) will remind you of this when the need for
disposing occurs
9