Adjusting The Cutting Depth - Flex MS 1706 FR Instrucciones De Funcionamiento Originales

 Screw on the quick-release clamping nut.
Depress the spindle lock (12) and manually
tighten the quick-release clamping nut (a).
 Gently depress the milling unit and attach
the guard hood (3).
 Lift lock (5) for guard hood and rotate
by 180° until it engages.
 Insert the mains plug into the socket.
 Switch on the wall chaser (without locking
the switch) and leave running for approx.
30 seconds. Check for quiet running.

Adjusting the cutting depth

1. Pull out the mains plug.
2. Depress the lock on the milling depth
stop (2b) and set the stop to the required
depth. Lock the milling depth stop (2b) at
the required depth.
22
Dust extractor
`^rqflk>
aìêáåÖ=çéÉê~íáçå=íÜÉ=ï~ää=ÅÜ~ëÉê=ãìëí=ÄÉ=
ÅçååÉÅíÉÇ=íç=~=Çìëí=Éñíê~ÅíçêK=
qÜÉ=Éñíê~Åíáçå=ëóëíÉã=ãìëí=ÄÉ=~ìíÜçêáëÉÇ=
íç Éñíê~Åí=ëíçåÉ=ÇìëíK=
^å=~ìíÜçêáëÉÇ=ëéÉÅá~ä=Éñíê~Åíçê=ãìëí=ÄÉ=ìëÉÇ=
íç=Éñíê~Åí=é~êíáÅìä~êäó=Ü~êãÑìäI=Å~êÅáåçÖÉåáÅI=
Çêó=ÇìëíK
fÑ=íÜÉ=Éñíê~Åíáçå=ëóëíÉã=ã~äÑìåÅíáçåëI=ëíçé=
ïçêâáåÖ=áããÉÇá~íÉäó=~åÇ=ëïáíÅÜ=çÑÑ=íÜÉ=éçïÉê=
íççäK=oÉé~áê=íÜÉ=Ñ~ìäí=ÄÉÑçêÉ=ëïáíÅÜáåÖ=çå=íÜÉ=
éçïÉê=íççä=~Ö~áåK
 Connect the hose from the extraction
system to the intake flange.
Check the attachment! If required, use
an appropriate adapter.
Making cuts
t^okfkd>
qÜÉ=ëíáéìä~íÉÇ=ÅìííáåÖ=ÇáêÉÅíáçå=áë=áåÇáÅ~íÉÇ=Äó=
íÜÉ=ÅìííáåÖJÇáêÉÅíáçå=~êêçï=ENMF=çå=íÜÉ=Öì~êÇ=
ÜççÇ=~åÇ=ãìëí=~äï~óë=ÄÉ=çÄëÉêîÉÇK
^äï~óë=ÖìáÇÉ=íÜÉ=ï~ää=ÅÜ~ëÉê=ïáíÜ=ÄçíÜ=Ü~åÇëK=
rëÉ=íÜÉ=ÇÉëáÖå~íÉÇ=ÖêáééáåÖ=~êÉ~ëK=
låÉ Ü~åÇ çå=íÜÉ=éçïÉê=íççäI=íÜÉ=çíÜÉê=Ü~åÇ=
çå íÜÉ=Ü~åÇäÉ=EQF=çê ETFK
fÑ=íÜÉêÉ=áë=~=êáëâ=çÑ=ÅìííáåÖ=íÜêçìÖÜ=äáîÉ=Å~ÄäÉëI=
Çç=åçí=íçìÅÜ=íÜÉ=ãÉí~ä=é~êíë=çÑ=íÜÉ=ã~ÅÜáåÉK
aá~ãçåÇ=ÅìííáåÖ=ÇáëÅë=ÄÉÅçãÉ=îÉêó=Üçí=ÇìêáåÖ=
çéÉê~íáçåK=aç=åçí=íçìÅÜ=íÜÉã=ìåíáä=íÜÉó=Ü~îÉ=
ÅççäÉÇ=ÇçïåK
1. Position the power tool milling table (1) fully
on the area which is to be processed.
To align with marks, use the notch in the
milling table.
Wall chaser MS 1706 FR