Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
All suction connections must be airtight. Make sure suction
lift is not more than 15 feet (4.6M). Fill pump body through
priming port before starting pump. Start pump; it should
pump water in under 10 minutes (depending on length of
suction hose and height of pump above water).
ELECTRICAL
Risk of dangerous or fatal electric shock.
Unplug pump before servicing it. Do not
handle pump or attempt to work on pump
with wet hands or while standing on wet or damp floor.
Plug pump into 115 Volt, 60 Cycle outlet only. Pump is
equipped with 3-wire, grounded, cord and plug. Do not modi-
fy or remove plug. Plug in to properly grounded, grounding
type outlet only. Make sure pump circuit meets National
Electrical Code. To avoid dangerous electrical shock hazard,
keep cord dry at all times.
NOTICE: Pump motor is equipped with carbon brushes (Fig.
2, Key 7) with a normal operating life of app. 150 hours. One
extra set of brushes is included. Replacement brushes are
available from your dealer. Motor brushes not included in
warranty.
Fire hazard. Incorrectly mounted brushes
may cause fire. Be sure curve on end of brush matches
curve on commutator.
LUBRICATION
Motor is lubricated at factory for life of bearings. Pump seal
is water cooled and self lubricating.
PUMP SERVICE
Motor has auto-reset thermal overload. If motor overheats,
overload will cut off power to prevent damage and will reset
after motor cools. If overload trips repeatedly, check pump for
cause (low voltage, clogged impeller, etc.).
Suction
Lift
5 (34.5)
0' (0M)
21.2 (80.2)
5' (1.5M)
19.5 (73.8)
10' (3M)
17.5 (66.3)
15' (4.6M)
15.6 (59)
NOTE: Performance does not take into account pressure losses in suction and discharge piping.
EXPLODED VIEW
Utility Pump
2A
2
1
PERFORMANCE CHART
Discharge Pressure (PSI) (kPa)
10 (68.9)
15 (103.4)
20 (137.9)
20.3 (76.8)
18.6 (70.4)
16.2 (61.3)
18.5 (70)
17.0 (64.3)
15.0 (56.8)
16.6 (62.8)
15.5 (58.7)
13.8 (52.2)
14.8 (55)
13.9 (52.6)
12.6 (47.7)
3
4
Hazardous voltage. Can shock, burn, or
cause death. Disconnect motor from electrical power
before servicing pump.
Always replace both brushes - to avoid fire hazard, never
replace just one.
Motor Brush Replacement:
Replace brushes when they wear down to 1/2" (12.7mm)
length.
1. Unplug pump from power outlet.
2. Unscrew brush caps (Fig. 2, Key 6) and remove brushes
(Key 7).
NOTICE: Pull brushes straight out of holders, being care-
ful not to stretch springs. If reusing same brushes, mark
brush and brush cap for replacement to original position.
3. Install new brushes and brush caps.
NOTICE: When reinstalling same brushes that were
removed, replace on same side of motor they were on
originally. Match curve on ends of brushes to curve on
commutator.
Brush
Cap
25 (172.4)
30 (206.8)
13.0 (49.2)
9.7 (36.7)
12.2 (46.2)
9.2 (34.8)
11.3 (42.8)
8.6 (32.6)
10.3 (39)
7.8 (29.5)
REPLACEMENT PARTS LIST
MODEL FPOC1500-01
Key
No.
Part Description
1
Pipe to Hose Adapter (2 Incl.)
2
Pump Body
2A
Priming Plug with O-Ring
3
Overhaul Kit - Includes: Diffuser Impeller,
Shaft seal, Slinger, Square cut O-Ring
4
Brush Kit - Includes 1 Set:
Brush Holder Cap (2 Req.)
4
Brush (2 Req.)
875 0993
3
Carbon Brush
w/Spring
Brush
Cap
Carbon Brush
w/Spring
150 0893
Figure 2 – Typical Installation
35 (241.3)
40 (275.8)
6.6 (25)
3.1 (11.7)
6.3 (23.8)
2.8 (10.6)
5.9 (22.3)
2.6 (9.8)
5.3 (20.1)
–
Symbol
U78-938P
C176-60P
U178-940P
FPKG 192
FPKG 193
}
Gal.(L)
per
Min.
Part
Publicidad
Tabla de contenido
